Technical Assistance - Legacy FLEXZILLA Levelwind Serie Manual De Instrucciones

5) Pull swivel assembly firmly from hose spool( SEE FIG. 13 and 14 ).
6) Unscrew Hose Clamp and pull hose off hose barb on swivel.
(SEE FIGURE 15)
7) Pull remaining length of hose out reel opening located at the reel front.
8) Take replacement hose through opening located at the front of reel.
Thread hose through hose leveling mechanism. (SEE FIGURE 16)
9) Insert hose through the center of the hose spool. Four openings are
referenced with the following hose I.D. dimensions located at the center
of hose spool: 3/8 in., 1/2 in.,5/8 in. & 3/4 in.. Locate the hose I.D. and pull
through that opening. (SEE FIGURE 17) Pull enough hose to allow the
hose to connect to hose barb on swivel.
10) Replace hose onto hose barb, tighten hose clamp onto hose & place
swivel into hose spool housing.
11) Replace wear ring and fasten with wear ring screws. Replace wear plate
so that the swivel drive tabs insert into wear plate tab receivers.
(SEE FIGURE 18)
12) Replace sideplate so that the plate snaps flush to side of reel. Turn
sideplate until locking tabs connect to sideplate.
13) Turn swivel so that fastener holes of swivel and sideplate align. Replace
the four sideplate fasteners and tighten.
14) Remove screw driver.
15) Retract hose back into reel
Swivel Kits
Levelwind Series Model #
L8305 - All Models/ L8306 - All Models/
L8310 - All Models
L8335 - All Models/ L8345 / L8350 / L8340FZ
L8344 / L8346 / L8349
1) Repeat steps 1- 6 in the HOSE REPLACEMENT procedure.
2) Place hose onto hose barb of new swivel body. Tighten hose clamp onto
hose & place swivel into hose spool housing.
3) Replace wear ring and fasten with wear ring screws. Replace wear plate
so that the swivel drive tabs insert into wear plate tab receivers. (SEE
FIGURE 18)
4) Replace sideplate so that the plate snaps flush to side of reel. Turn
sideplate until locking tabs connect to sideplate.
5) Turn swivel so that fastener holes of swivel and sideplate align.
Replace the four sideplate fasteners and tighten.
6) Remove screw driver.
7) Retract hose back into reel.
Levelwind Troubleshooting Guide
TM
Troubleshooting Questions
1. Hose will not retract back into the unit.
2. Hose will not fully retract back into the unit.
3. Hose will not lock in 3' intervals.
4. Internal leak.
Replacement Replacement
Swivel Body Hose Stopper
Part # Part #
RP005007-38 RP005026
RP005007-12 RP005027
RP005007-58 RP005028
Suggested Tips
1a. Ensure the Latch Spring & Pawl isn't engaged
1b. Follow the Tension Adjustment Procedure (See pg 2)
1c. Replace Internal Drum Assembly
2a. Follow the Tension Adjustment Procedure (See pg 2)
2b. Is the replacement hose too heavy? (Rubber?)
2c. If hose bunches, adjust the Layering Mechanism Timing
3a. Are you releasing the hose too quickly?
3b. Is the Latch Spring & Pawl engaged?
3c. Replace the Latch Spring & Pawl Mechanism
4a. Replace the hose if it is damaged.
4b. Replace the Swivel Body (a-rings are not available separately)

TECHNICAL ASSISTANCE:

Call 800-645-8258 or email service@legacy
mfg.com if you have any questions regarding the
installation or operation of this reel.