Installation Instructions; Tools And Parts; Location Requirements; Required Cutout Dimensions - Kenmore 204.23069610 Instrucciones De Instalación

Marco del horno incrustado de microndas
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Tools and Parts

Tools Needed
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools
listed here.
Measuring tape
Pencil
Phillips screwdriver
Parts Supplied (not shown to scale)
Rear duct
Bottom duct
The insulating
Trim kit frame
strip
Note: The Rear duct is only to be used with microwave model: 204.77603610

Location Requirements

The microwave oven may be installed over a built-in wall oven. If
installing over a built-in oven, make sure there is a minimum of 3"
(7.6 cm) between the top of the lower oven cutout and the
microwave oven cutout floor.
The microwave oven may also be installed in a cabinet by itself
(without a built-in oven below). For best usability, we recommend
a minimum distance of 36 1/8" (91. 7cm) from the floor to the
microwave oven cutout floor.
Make sure the surrounding cabinetry has clearance to open and
close freely. Allow a clearance of at least 1
cutout floor (3" [7.6 cm] for installation above a built-in oven), and
a clearance of at least 2" (5.1 cm) above the cutout opening.
2"
(5.1 cm)
B
1
9/16
"
(4.0 cm)
D
E
A. Upper cabinet
B. Microwave oven cutout
C. Lower oven cutout

INSTALLATION INSTRUCTIONS

Drill
7/64" drill bit
Rails (2)
Shortest
Short
Long wood screws
screws(12)
screws(9)
(4 + 2 extra)
(10+2 extra)
(7+2 extra)
" (4. 0 cm) below the
9/16
A
B
C
36
"
1/8
(91.7 cm)
D. Lower cabinets
E. Floor

Required Cutout Dimensions

17" (43.2 cm)
min.
"
(43.5 cm)
17
1/8
max.
3"
(7.6 cm)
NOTES:
Height dimension is critical: 17" (43.2 cm) minimum, 17
(43.5 cm) maximum.
Width and depth measurements have ±1/16" (2 mm)
tolerance.
3" (7.6 cm) minimum dimension is from lower oven cutout
ceiling to microwave oven cutout floor.
Trim kit frame extends 1
cutout opening.

Trim Kit Frame Dimensions

19
"
1/11
(48.5 cm)
2"
(5.1 cm)
* 30 ( 76.2 cm ) trim kit
"
3"
(7.6 cm)
EN-2
22
"
3/4
(57.8 cm)
h W i
h
d t
d t
W i
23
" (58.7 cm)
1/8
" (2.7cm) above and below the
1/16
*
"
29
(75.6cm)
3/4
"
23
(
58. 4cm)
3
"
9/17
(8.8 cm)
3
"
(
8.1 c
m)
7/18
1
3/16 "
1
1/16"
(2.7 cm)
A
1
"
1/16
(2.7 cm)
B
1/8"
"
12
(30.9 cm
)
(
3.0 cm
)

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

204.23063610

Tabla de contenido