Operating Tips And Recommendations; Automatic Filter Refill Program; Storage; Troubleshooting - Vornado evap3 Guía Para El Usuario

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Operating Tips and Recommendations

For best results:
1.
Allow for optimum airflow by keeping the grill unobstructed.
Ensure curtains and other items are far enough away from the
unit to not be pulled into the side inlets or interfere with airflow.
2.
Do not turn the unit off and on - allow your Humidifier to
operate continuously. This will help maintain the desired
humidity level in your home, cost only pennies a day, and will
not damage the unit.
It is normal and expected for your Humidifier to run continuously
for a few days in order to raise the moisture content of the air
to the desired level upon initial use or if the air is extremely dry.
When your home and its furnishings have absorbed sufficient
moisture and become stabilized at the desired humidity level, the
amount of water used will decrease.
If you operate your Humidifier continuously, it may need to be
refilled with water every day. Simply look through the Water Tank
to be certain that there is adequate water supply for operation.
When the water level drops below the operating level, the unit will
not be producing humidity.
Protect the Water Tank from damage. Any cracks or damage to the
Tank may cause it to leak water onto the floor or other surfaces.
If the Humidifier is turned Off, with water in the unit, and not
turned back on for 8 hours or longer, or if the unit is not cleaned
as recommended, you may experience some growth of algae
or bacteria. These microorganisms may become airborne.
Thoroughly clean the unit to eliminate any microorganisms (See
CLEANING AND MAINTENANCE for instructions).
Your Evaporative Vortex Humidifier is effective at supplying
necessary moisture to dry air. It should be used with proper care
to prevent over-humidification. To know if the humidity level is too
12 English
high, gauge the condensation or frost on windows. Adjust your
Humidifier to a point where this condition is at a minimum.

Storage

1. Thoroughly clean unit (See CLEANING INSTRUCTIONS).
2. Remove and discard used Filters (See FILTER REPLACEMENT).
Be sure to buy a new Filters now so you are ready for next
season!
3. Empty Water Tank and Base. Let unit dry completely.
4. Place in original retail carton if available.
5. Your Humidifier is now ready for Storage.
6. Store in a cool, dry location.
Note: It is recommended to clean the unit again before use.
Automatic Refill Program
Select the shipment interval and Vornado will
send replacement Filters automatically. Elimi-
nate the hassle of remembering to reorder.
Maintain the high efficiency of your Vornado
Humidifier.
To sign up, visit www.vornado.com, email
consumerservice@vornado.com or call
Part # MD1-0002
1-800-234-0604. Cancel at anytime.
Problem
Possible Cause and Solution
Unit fails to power on.
Unit is not plugged in. Plug power cord into electrical outlet.
Household circuit breaker / ground fault interrupter has tripped or blown a fuse. Reset circuit breaker /
ground fault interrupter, or replace fuse. For assistance, contact a licensed electrician.
The unit has blown a fuse. Cease usage and unplug. Contact Consumer Service for assistance.
Unit is damaged or in need of repair. Cease usage and unplug. Contact Consumer Service for assistance.
Unit makes a bubbling or
This is normal. Water is being dispensed into Base.
gurgling sound.
Unit is not producing
Water level in Tank is empty or too low. Refill with clean, cool tap water. (See FILLING WATER TANK for
desired amount of
instructions.)
humidity.
Unit has reached its set point. When set humidity level is reached, the Fan will turn off until humidity level in
the room drops below humidity set point.
Airflow is blocked. Remove obstruction.
Unit settings are too low. Set to High Fan Speed and Continuous Humidity for maximum humidity output.
Filters are in need of re-
The additional sodium in chemically softened water may cause Filters to harden or become mushy. Try using
placement too often.
untreated tap water or distilled water.
Try adding Bacteriostat or Water Treatment found at most hardware or home specialty stores to the water.
Or periodically remove the Filters and clean, by soaking them in cool tap water and two teaspoons of white
vinegar. Let stand 20 minutes, then rinse in cool water. Allow excess water to run off and dry before replacing
them in the Base. DO NOT wring.
Water is too hard. Use distilled water.

Troubleshooting

English 13

Publicidad

Tabla de contenido
loading

Tabla de contenido