Akron STYLE 3578 STREAMMASTER Instrucciones De Instalación, Funcionamiento Y Mantenimiento página 6

STEP 5. Remove.the.cable.grip.nut.from.the.plastic.bag.and.put.it.on.the.other.end.of.the.cable.with.the.threads.. .
. facing.out . . Remove.6.inches.of.the.outer.cover.and.strip.back.3/8.inch.from.each.of.the.7.wires .
STEP 6 Remove.the.6.logic.box.cover.screws.and.set.the.logic.box.cover.aside . . Thread.the.7.wires.through.
. the.upper.or.lower.control.hole.in.the.logic.box.(see.component.layout,.Figure.5) . . Thread.the.cable.grip..
. washer.and.cable.grip.nut.with.the.threads.facing.the.box.on.the.cable . . Pull.enough.cable.through.the..
. cable.grip.to.ensure.a.good.fit . . Tighten.the.cable.grip.nut.and.attach.the.individual.wires.to.the.proper..
. terminals.(see.wiring.diagram.Figure.6) . . Reattach.the.logic.box.cover.and.secure.with.the.6.screws .
. . NOTE:..The.lower.control.and.upper.control.wires.must.be.attached.to.the.correct.terminals.for.the..
. . lower.control.to.override.the.upper.control . . The.one.attached.to.the.Master.terminal.will.have.the.
. . overriding.capabilities . . .Adjust.the.DIP.switch.settings.as.needed . . (Refer.to.the.description.below . )
B . . DIP.SWITCH.SETTINGS
. The.DIP.switches.are.located.in.the.logic.box.on.the.circuit.board .
. The.switches.are.factory.set.at:
1 2
ON
OFF • •
. Switch.1.-. Allows.the.ability.to.use.a.6-conductor.controller.for.the.Stow.controller.instead.of.10-conductor .
. . . ON.-.Enables.the.6-wire.Stow.controller
. . . OFF.-.Disable.the.6-wire.Stow.controller
. Switch.2.-. Allows.the.Stow.and.Deploy.switch.to.be.a.momentary.or.a.maintain.switch .
. . . ON.-.Requires.JOG.(maintain).to.Stow.or.Deploy.(No.Learn.mode.if.DIP.2.is.ON)
. . . OFF.-.Momentary.switch.to.start.the.Stow.or.Deploy.sequence.(factory.set)
. Switch.3.-.. RESERVED.FOR.FACTORY
. Switch.4.-. RESERVED.FOR.FACTORY
. Switch.5.-. Allows.the.nozzle.to.return.to.straight.stream.during.the.Stow.sequence .
. . . ON.-.Returns.the.nozzle.to.straight.stream.during.the.Stow.sequence
. . . OFF.-.Leaves.nozzle.pattern.set.where.last.used.(factory.set)
. Switch.6.-.. RESERVED.FOR.FACTORY
. Switch.7.-.. RESERVED.FOR.FACTORY
. Switch.8.-. RESERVED.FOR.FACTORY
C . . MONITOR.WIRING.HARNESS.ATTACHMENT
These.instructions.are.to.attach.the.monitor.wiring.harness.to.the.logic.box .
STEP 7. . R emove.the.cable.grip.nut.from.the.logic.box.for.the.wiring.harness.cable . . DO.NOT.REMOVE.THE.CABLE.GRIP . . Put.the.cable.
grip.nut.on.the.wiring.harness.cable.with.the.threads.facing.out . . Put.the.cable.through.the.correct.logic.box.cable.grip.(see.
component.layout,.Figure.5).so.the.cable.grip.nut.will.grab.the.outer.cover.of.the.cable . . Tighten.the.cable.grip.nut.and.attach.
the.individual.wires.to.the.proper.terminals.(see.wiring.schematic.Figure.6) .
D . . BATTERY.ATTACHMENT
The.battery.connections.should.be.the.last.connection.made .
STEP 8. . A UXILIARY.BATTERY.-.Remove.the.logic.box.cable.grip.nut.for.the.auxiliary.battery.and.place.it.on.the.battery.(#16-3).cable.
with.the.threads.facing.out . . Thread.the.cable.through.the.cable.grip.nut.until.the.cable.grip.will.grab.the.cable . . Tighten.the.
cable.grip.and.attach.the.individual.wires.to.the.proper.terminals.(see.wiring.schematic.Figure.6) .
. . . NOTE:..Auxiliary.Battery.is.not.intended.to.operate.the.monitor .
3 4 5 6
• • • •
7 8
• •
Page.4
. .
. . .
. . .