Heco Ascada 600 TOWER Notas Importantes Sobre La Instalación / Certificado De Garantía página 14

cOnnEcTing ThE pOWER supply Of ThE TRAnsmiTTER And ThE AcTiVE spEAKERs
Two power cables are supplied for the two floor-standing speakers. The mains cable used in your country, however,
may be different. If the mains cable is not compatible with your power sockets or if you are in any doubt, please contact
your HECO dealer.
1. Connect the power cables to the sockets (Fig. 4 (12)) and (Fig. 5 (24)) on the amplifier of the right and left speakers.
2. Plug the power cable into the power socket. Make sure that you are using the mains plug that is compatible with the
socket (refer to the information above).
cOnnEcTing AudiO sOuRcEs TO ThE RighT (mAsTER) spEAKER
plEAsE nOTE: Only the right (master) speaker can be connected to source devices. It passes on the signals for the
left channel automatically to the left (slave) speaker. The left (slave) speaker does not have any inputs that can be used
for playback.
1. Connecting to a pre-amplifier output/amplifier/AV receiver
Connect the right speaker to the pre-amplifier output of your pre-amplifier/amplifier/AV receiver using a stereo
connection cable.
2. Connect to a headphone jack or pre-amplifier output with 3.5mm jack
Use an RCA to 3.5mm jack adapter cable to connect the right speaker to the headphone jack on your amplifier, TV
set, MP3 player, smartphone, etc.
3. Connecting to a computer with a USB port
Connect the right speaker to the USB port on your computer by using a USB cable (type A to type B) (see Fig. 7).
A driver is not required. If you are prompted to make a selection, please select the SPDIF interface
„Ascada 600 Tower".
4. Connecting to digital audio sources
Connect the right speaker to the digital output on your CD player/computer/games console/network player, etc. by
using an optical or coaxial digital audio cable. The digital inputs can be selected separately, therefore it is possible to
connect two digital sources simultaneously.
plEAsE nOTE: The digital inputs are suitable for stereo signals up to 24 bit/96kHz
5. Connection to a Bluetooth device
Switch the active loudspeaker to the Bluetooth input. If you have previously connected a Bluetooth device, the
loudspeaker will automatically attempt to re-establish a connection with this device. If this is the case, you may be
required to manually reconfirm the connection on the source device.
If a connection has not already been made or the connection cannot be re-established, activate the ‚pairing mode'.
To switch the speaker to the pairing mode, briefly press the PAIR button (Fig. 6, (34)) on the remote control or press
and hold the volume/source button (Fig. 3, (7)) for at least 3 seconds. The blue STBY/Pair LED (Fig. 2, (3) will flash
quickly whenever the pairing mode is active.
Now activate the Bluetooth mode on your source device. The speaker will appear in the list of Bluetooth devices as
„Ascada 600 Tower". If it is not displayed in the list, set your source device to search for Bluetooth devices manually
and make sure that the speaker has been switched to the pairing mode.
Depending on the source device, you may be asked whether the password is to be accepted during the pairing
procedure. You can confirm this by simply pressing „Accept". If you are still asked for a password, use the default
passwords „0000" or „1234". If you are asked if you want to establish a connection after pairing, please select
„Yes". When the device has been paired and connected successfully the Bluetooth LED status indicator will illuminate
continuously and the STBY-Pair LED goes out.
The loudspeaker supports the „aptx®" high quality audio transmission standard. If your source device also supports
this standard, „aptx®" will be selected automatically as the transfer mode when establishing a Bluetooth connection.
plEAsE nOTE: Please check whether the output of the audio source
a) has a fixed volume level or
b) the level can be adjusted with the volume controller of the audio source.
In case a) you can adjust the volume using the remote control of the Ascada 600 Tower; in case b) the level of the audio
source should be set to a maximum level where no distortions can be heard at the highest volume setting of the Ascada
600 Tower. The volume of the audio source should also be taken into account. No distortions should be evident here
either.
14