Introduction; Device Description; Scope Of Delivery - Scheppach MTE460 Traducción De Las Instrucciones Originales De Funcionamiento

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 62

1. Introduction

Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear Customer,
we hope your new tool brings you much enjoyment
and success.
Note:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified,
• A breakdown of the electrical system that occurs
due to the non-compliance of the electric regu-
lations and VDE regulations 0100, DIN 57113 /
VDE0113.
WE RECOMMEND:
Read through the complete text in the operating in-
structions before installing and commissioning the
device.
The operating instructions are intended to help the
user to become familiar with the machine and take
advantage of its application possibilities in accord-
ance with the recommendations.
The operating instructions contain important infor-
mation on how to operate the machine safely, pro-
fessionally and economically, how to avoid danger,
costly repairs, reduce downtimes and how to in-
crease reliability and service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in
your country.
Keep the operating instructions package with the
machine at all times and store it in a plastic cover to
protect it from dirt and moisture.
Read the instruction manual each time before oper-
ating the machine and carefully follow its information.
The machine can only be operated by persons who
were instructed concerning the operation of the ma-
chine and who are informed about the associated
dangers. The minimum age requirement must be
complied with.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
In addition to the safety notices contained in this
operating manual and the particular instructions for
your country, the generally recognised technical reg-
ulations for the operation of identical devices must
be complied with.
We cannot accept any liability for damage or acci-
dents which arise due to a failure to follow these in-
structions and the safety instructions.
2. Device Description (Fig. 1-2)
1. Handle
2. Power cord
3. Frame tubing
4. lower bar
5. Machine frame
6. Blade roller
7. Wheel
8. Wheel cap
9. Carriage bolt
10. Wing nut (plactic)
11. Cable clip
12. Safety release catch
13. On/Off switch
14. Wheel suspension
15. washer (pre-assembled)
16. split pen (pre-assembled)
17. lock pen
18. Screw M8
19. Nut M8
20. Drive shaft
3. Scope of delivery (Fig. 2)
• 1x Handle (1)
• 1x Machine frame (5)
• 1x Frame tubing(3)
• 4x Carriage bolt (9)
• 4x Wing nut (plactic) (10)
• 2x Cable clip (11)
• 2x Wheel (7)
• 2x Wheel cap (8)
• 1x Manual
• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for trans-
port damage. When complaints the dealer must be
informed immediately. Subsequent complaints will
not be accepted.
• If possible, store the packaging until the warranty
period has expired.
GB | 23

Publicidad

Tabla de contenido
loading

Tabla de contenido