Sammic CK-35V/38V Instrucciones página 15

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 1
- Lift the plunger (M) and turn it anti-clockwise to release the food insertion area of the standard hopper (K). The plunger (M) can be left resting on the
plunger support (M). The motor will stop.
- Insert the products into the standard hopper (K).
- The motor starts and the cutting process begins when the plunger (M) is rotated clockwise. Feed the product by gently lowering the plunger (M). Repeat
the process as many times as required.
- Press "Stop" (4) to finish.
Operation with cylindrical hopper (L). CK-35V/38V, CK-45V/48V and CA-3V/4V.
This Ø 55 mm hopper is used to cut long, cylinder-shaped vegetables such as carrots, endives, cucumber, etc.
- Start the machine.
- Release the mallet (L) by rotating it clockwise.
- Insert the products through the hole and push them gently with the "Mallet" (L). Repeat the process as many times as required.
- Press "Stop" (A) once production has finished.
IMPORTANT: Leave the mallet (L) inside the cylindrical hopper when the latter is not in use.
Operation of the CK-35V/38V, CK- 45V/48V and CA-3V/4V with tube head.
- The tube head is must be mounted and locked in place.
- Start the machine.
- Insert the products through the upper holes in the tube head. The cutter will stop automatically after working for 30 minutes. To continue, press "Start"
again.
- Press "Stop" (4) to finish.
"Cutter" operating mode (CK-35V/38V, CK- 45V/48V and KE-5V/8V)
With the machine disconnected from the mains:
- With the bayonet mechanism (Y) open (AA), place the "Cutter" accessory on the motor block so that the three lugs are inserted into the holes of the
quick-lock mechanism. The handle must be placed just above the keypad for the machine to operate. Close (Z) the bayonet mechanism (Y) to lock the
accessory on the motor block.
Fit the "Blade assembly" (T) and close the lid (U) by turning it anticlockwise until it is engaged and locked. The lid (B) has a hole through which to feed the
product while the machine is operating and a scraper which, when rotated, stirs the contents of the vessel (S) so that they are processed more evenly.
When the machine is switched on the screen will display Icon No. 5 (represented by the rotor) together with the speed level and the associated RPM. The
speed can be adjusted with the motor running or stopped.
The motor starts when the "Start" key (A) is pressed and will run until the same key is pressed again or the PULSE B key is held down. It also starts and
runs while the PULSE B key is held down. The icon rotates while the motor is running.
The motor rotation direction can be reversed by pressing the C key, either with the motor running or stopped. The associated icon appears on the screen
and the speed level is represented by the "-" sign, indicating reverse. With the motor running the icon then rotates in the opposite direction.
Each time the bowl is fitted (with each new process) and the motor starts, a counter appears that counts the duration of the process. This time is reset
only when the bowl is removed.
The countdown time can be set by pressing the CLOCK "D" key when fitting the bowl. Accept by pressing the same key again or starting the motor. The
countdown will then start. The timer has an associated indicator circle (2) that provides a visual reference of the time remaining until the end of the process.
When the time reaches zero the motor stops and a "beep" is emitted.
FORCE CONTROL function
With the motor running, ring 3 on the screen indicates load under which it is working. When the indicator approaches the red zone, it means that the motor
is nearing overload. This level varies depending on the features of the product being processed.
CLEANING
Cleaning of the "Vegetable Cutter" accessory CK-35V/38V, CK- 45V/48V and CA-3V/4V:
- Release the lock (I) and open the hinged cover (J).
- On the CK-45V/48V and CA-4V, holding the disk (A) with your hand without touching the blades, use the key (P) supplied with the machine to remove
the bit (Q) or the mixer (R), unscrewing it anticlockwise.
- Remove the disk (A) by turning it clockwise and carefully pulling it upwards. Remove the grid (B) and the ejector (C).
- In the CK-35V/38V and CA-3V the plunger (M) and hinged lid (J) can be dismantled for cleaning. The pins (N and O) must be removed to do so.
WARNING: To be able to remove the products embedded in the grids (B), simply tap them in the cutting direction with an elongated potato or
a whole carrot. This prevents damaging the grid (B). Take care with the edge of the grid (B). Never use hard objects to tap the grid (B).
There is also a grid cleaner in the Sammic catalogue for the FMC-8D and FMC-10D grids.
The SH grater disks are designed so that the plate can be separated from the frame for cleaning.
Cleaning the "Cutter" accessory (CK-35V/38V, CK- 45V/48V and KE-5V/8V):
-15-
EN

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Ck-45v/48vCa-3v/4vKe-5v/8v

Tabla de contenido