Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
heavy enough to carry the current your product will
draw. An undersized extension cord will cause a drop
in line voltage resulting in loss of power and overheat-
ing. Table 1 shows the correct size to use depending
on cord length and nameplate ampere rating. If in
doubt, use the next heavier gage. Number, the heav-
ier the cord. To reduce the risk of disconnection of
appliance cord from the extension cord during oper-
ating: Make a knot as shown in Fig. 2;
Volts
120V
Ampere Rating
More than Not more than
0-6
6-10
10-12
12-16
METHOD OF SECURING EXTENSION CORD
CORD SET
APPLIANCE CORD
(A) TIE CORD AS SHOWN
17. DO NOT FORCE TOOL. The correct tools will do the
job better and safer at the rate for which it is
designed.
18. DISCONNECT THE PLUG FROM THE POWER
SOURCE BEFORE MAKING ANY ADJUSTMENT,
CHANGING ACCESSORIES, OR STORING THE
TOOL. Such preventive safety measures reduce the
risk of starting the tool accidentally.
19. STORE IDLE TOOLS INDOORS. When not in use,
tools should be stored indoors in dry, and high or
locked-up place, out of reach of children.
20. MAINTAIN TOOLS WITH CARE. Keep cutting tools
sharp and clean for best performance and to reduce
the risk of injury. Follow instructions for lubricating
and changing accessories. Inspect tool cord periodi-
cally, and if damaged, have it repaired by an author-
ized service facility. Keep handling surface dry,
clean, and free from oil and grease.
21. CHECK DAMAGED PARTS. Before further use of
the tool, a guard or other part that is damaged
should be carefully checked to determine that it will
operate properly and perform its intended function.
check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and any
RULES FOR SAFE OPERATION
Total length of cord in feet
100
150
25
50
18
16
16
16
18
16
14
14
16
16
14
14
14
12
Not recommended
TABLE 1
(B) CONNECT PLUG AND
RECEPTACLE
Fig. 2
other condition that may affect its operation. A
guard or other part that is damaged should be prop-
erly repaired or replaced by an authorized service
center unless indicated elsewhere in this manual.
SHREDDER SAFETY RULES:
1.
Extreme caution should be taken to ensure shredda-
ble material does not contain metal. Rocks, bottles.
Cans or other foreign objects.
2.
Do not allow hands or any other part of the body, or
clothing to enter inside the feeding chambers or dis-
charge chute, while machine is operating.
3.
Wear gloves while operating the machine.
4.
Before starting the machine, ensure that all screws
and other fasteners are properly secured.
5.
Machine should be operated on firm level surfaces
only.
6.
Before starting the machine, check that the
chamber is empty.
7.
Motor should be kept clean of debris and other
accumulations.
8.
Keep all guards and deflections in good working
condition.
9.
Stand clear of discharge chute at all times.
10. Do not over reach and keep face and body back form
the feed opening.
11. Never pull the machine by the power cord and keep
cord away form water or sharp edges.
12. Disconnect the power cord when the machine is not
in use.
13. If machine should become clogged, switch off the
motor, disconnect the power cord, make sure all mov-
ing parts are completely stopped before
clogged debris.
14. Ensure the power cord is always in good condition. A
cord with
broken insulation is extremely dangerous
and can result in fire, electric shock or
sonal injury.
15. The operation of any tools can result in foreign objects
being thrown into your eyes, which can result in
severe eye damage Before operating power tool,
always wear safety goggles or safety glasses with side
shields and a full face shield when needed. We rec-
ommend wide Vision Safety Mask for use over eye-
glasses or standard safety glasses with side shields.
4
cutting
cleaning
serious per-
Publicidad
Tabla de contenido
