Care And Cleaning - Energy Power Bar Manual Del Propietário

each press. If the unit has successfully learned the function, on the fourth press of
the button, the light will flash GREEN several times and then turn to solid GREEN.
(Remember to use the SOURCE, VOLUME UP & VOLUME DOWN in place of <MUTE>
when programming the other buttons during this step)
To program the remaining functions, simply repeat all steps, substituting <MUTE> with
the new function and button presses (SOURCE, VOLUME UP, and VOLUME DOWN) on steps
TWO and THREE.
ImPortant notE:
There is not a power on/off button on the front of the soundbar
(there is a "Main Power" switch on the soundbar's rear panel). You Do not need to turn
off the soundbar (or subwoofer) when finished watching TV. When finished, turn off your
TV (or Satellite or Cable box if the soundbar is connected to that). The soundbar (and the
subwoofer) will automatically go into a Standby or "sleep" mode if they do not receive an
audio signal from your TV, Satellite or Cable Box for approximately 10 minutes. Standby
"On" mode is indicated by a solid red status light on the soundbar front and on the
subwoofer rear panel. When your TV, Satellite or Cable box is turned back on and a signal
is again received the soundbar (and subwoofer) will automatically come out of Standby
mode and turn on.
oPEratInG thE EnErGy PoWEr
Once your soundbar is connected and operating, you will want to complete a few basic steps
to get the most enjoyment out of your system. First, you will want to turn off the speakers
on your TV and let your soundbar be your new sound source. Some TV's will automatically
turn off their speakers when you connect the soundbar, while others you must manually turn
their speakers off. Each TV is different, but to manually turn off TV speakers you usually
must bring up a menu of some type, and go into that menu's "audio" or "sound" portion
where you find a selection to turn TV speakers off. If you cannot turn your TV speakers off,
the soundbar will still give you an excellent enhancement to the sound coming from your TV,
and you can easily adjust your TV sound to blend with the soundbar's sound. To make this
adjustment, first program your TV remote to operate the soundbar, then manually turn your
TV volume down all the way down from the controls on the TV itself. Next, press the VOLUME
UP (+) control on the front of the soundbar until you have a comfortable TV listening volume
level coming from the soundbar. Finally, to make sure the Energy Power Bar subwoofer has
a balanced sound with the soundbar, set the subwoofer volume on the subwoofer rear to
approximately the halfway point, and then adjust up or down.
troUBLEShootInG
Soundbar does not power on
• Is the power supply plugged into a "live" outlet?
• Is the soundbar "Main Power" rear switch on?
no sound from soundbar
• Is it plugged into a "live" outlet and "Main Power" rear switch on?
• Are all connections from TV/Cable or Satellite box pushed in tightly?
• Is TV/Cable or satellite box turned on and the volume turned up?
• Is the soundbar volume turned up?
• Is the soundbar "STANDBY" off? (LED green or orange solid)
• Is the soundbar on the correct source input?
• If using digital optical hookup, make sure TV/Satellite or Cable box is outputting
PCM sound, NOT Dolby Digital
®
no sound from subwoofer
• Is it plugged into a "live" outlet and "Main Power" rear switch turned on?
• Is the rear subwoofer volume control turned up?
• Has the subwoofer "paired" with the soundbar?
Bar
™
Subwoofer will not wirelessly "pair" with the soundbar
(subwoofer green status lights continue flashing)
• Move subwoofer closer to soundbar
• If other wireless devices nearby (i.e. baby monitors. cordless phones, Wi-Fi, etc.)
have multiple channel selection, switch their channel
• Turn both the soundbar and subwoofer off, then turn on again to initiate a new
pairing sequence.
tV/Cable Box/Satellite Box remote Will not Program
• Carefully follow all programming instructions
• Program your original TV remote to the soundbar, then try using your universal
remote without programming it.
• You may need to repeat the programming of a function in some cases
• There may be some cases where the soundbar will not be able to learn all remote
control codes
For Questions, contact Energy Customer Service:
In the United States: 1-866-441-8208

CarE anD CLEanInG

Occasional dusting or wiping of the cabinets with a soft cloth is all that is required. Never
use water, abrasive or solvent type cleaners or detergents. Never spray polishes or cleaners
on the drive units (woofer, midrange or tweeter) or on any controls or connection points. A
vacuum cleaner with a soft brush attachment may be used to clean the grille fabric.
Energy is a registered trademark of Audio Products International Corp., a wholly owned subsidiary of
Klipsch Group, Inc.