Manual Release Mechanism; Electronic Programmer; Important Remarks - Cardin SL Serie Manual Del Usuario

INSTRUCTIONS FOR POSITIONING THE UNIT
7
- The geared motor unit has been assembled in
the factory to be fitted to the LEFT SIDE of the
gate (internal view). To install the motor to the
RIGHT of the gate set dip "8" of the dip-switch
"S1" (fig. 3) to "ON".

MANUAL RELEASE MECHANISM

All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
Manual release is carried out with the power to the motor interrupted
due to a power failure. To release the gate use the manual release key
supplied with the unit. The key should be kept inside the house in an
easily accessible place or stored with the unit itself.
8
A
To release the unit
Remove the cover "A" using a screwdriver and insert the key "B" over
the T-shaped pin, then rotate the key through 90 degrees in the direction
indicated by the arrow "C" (clockwise). This will release the clutch and
separate the gears from the motor allowing you to manually manoeuvre
the gate by pushing lightly on it.
To relock the unit
Follow the above instructions in reverse order rotating the key through
90 degrees in the direction indicated by the arrow "D" (anticlockwise). SCALA: 1:2
Description : Prodotti Technocity
Drawing number : DI0130
Close the release mechanism access cover "A".
Sblocco motore
Product Code : SL4024
Date :
Draft : P.J.Heath 11-06-98
Attention! Never use the manual release mechanism while
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
the gate is in operation. If you release the gate and then
give a movement command the following symbol appears
on the display .
Access to the electronic card
To open the cover insert a screwdriver into the slot "G" and turn it
through 90° as shown in fig. 8.
Caution! Before opening the cover make sure that the
power has been switched off at the mains.

ELECTRONIC PROGRAMMER

Electronic programmer for a dc motor with an incorporated radio receiver
card, which allows the memorisation of 300 user codes (see "remote
control" page 20). The "rolling code" type decoder uses 433.92 MHz
series transmitters.
The motor rotation speed is electronically controlled, starting slowly
and increasing in speed; the speed is reduced as it nears the travel
limit so as to enable a controlled smooth stop.
Programming is carried out using one button and allows you to set the
current sensor and the entire gate travel distance.
The logic carries out position control using an encoder.
The intervention of the anticrush/antidrag sensor during the closing
and opening stages causes a brief (10 cm) travel direction inversion
then a block.
ON
1 2 3 4 5 6 7 8
F
G
9 0 °
B
C
D

IMPORTANT REMARKS

• After having installed the device, and before powering up
the programmer, release the gate (manual release mecha-
nism) and move it manually, checking that it moves smoothly
and has no unusual points of resistance.
• The programmer can activate the motor automatically.
This is indicated by the warning lights pre-flashing for 10
seconds, and by the symbol
("automatic repositioning" on page 19).
• The programmer is fitted with an electrical input monitor-
ing system, which is used to block the motor in emergency
conditions; however this system is not active during the first
second of each manoeuvre.
Do not therefore attempt to physically block the door during
these stages.
If you need to check the status of the fuses, disconnect the
power supply to the programmer; reconnect it only after
having re-inserted the fuse.
• The presence of the electrical input monitoring system does
not exclude the need to install photoelectric cells or other
safety devices which are foreseen by the local standards
and regulations in force.
• The geared motor unit has been assembled in the factory
to be fitted to the left side of the gate. Read the paragraph
"instructions for positioning the unit".
• For the correct operation of the programmer the incorpo-
rated batteries must be in good condition: the programmer
will lose the position of the gate in case of blackouts when
the batteries are flat, the alarm will sound and automatic
repositioning will take place .
Check the good working order of the batteries every six
months (see page 21 "Battery check").
• Before connecting the appliance make sure that the voltage
and frequency rated on the data plate conform to those of
the mains supply.
• An all pole trip switch with at least 3 mm between the
contacts must be installed between the unit and the mains
supply.
• Don't use cables with aluminium conductors; don't solder
the ends of cables which are to be inserted into the bind-
ing posts; use cables marked T min 85°C and resistant to
atmospheric agents.
• The terminal wires must be positioned in such a way that
both the wire and the insulating sheath are tightly fastened
(a plastic jubilee clip is sufficient).
ELECTRICAL CONNECTION 230 Vac
• Connect the control and security
device wires.
• Run the 230 Vac mains power
supply through the trip switch "TS"
and the through the cable clamp
"PS" to the terminal board:
- connect the live to post 1
- connect the earth to post 5
- connect the neutral to post 2 N
If you need to check the status of the fuse "F1", discon-
nect the power supply to the programmer; reconnect it
only after having re-inserted the fuse.
16
appearing on the display
230Vac
N L
TS
L