Briteq BT-Dazzle Manual De Instrucciones página 7

ENGLISH
Use [DOWN] and [UP] buttons to choose [3MSL], [14CH] or [16CH] mode.
 Once the desired channel setup mode is shown on the display, press the [ENTER] button to select it.
 Press the [MENU] button for about 2 seconds to store the setting and to return to running mode.
Show Mode
Used to set the projection area of the beams when used in standalone or master/slave mode.
 Press the [MENU] button until [Show Mode] is showing on the display.
 Press the [ENTER] button, the display starts blinking.
 Use [DOWN] and [UP] buttons to select one of the available shows:
 Show 1: Fixture is placed on the floor. Tilt movement angle 210°.
 Show 2: Fixture is fixed under ceiling. Tilt movement angle 90°.
 Show 3: Fixture is placed on a podium, in front of the audience. The spot is always projecting to
the audience's direction; i.e. in front of the stage. Pan movement angle (left to right to left): 160°. Tilt
movement angle: 90° (60° above horizon; 30° below horizon.)
 Show 4: Fixture is fixed under ceiling. The spot is mainly projecting in front of the stage. Pan
movement angle (left to right to left):160°. Tilt movement angle: 90° (vertically, front 75°; back
15°)
 Once the right mode is shown on the display, press the [ENTER] button to select it.
 Press the [MENU] button for about 2 seconds to store the setting and to return to running mode.
Slave Mode
Used to make the slave unit work in opposite to the master or to work in complete sync.
 Press the [MENU] button until [Slave Mode] is shown on the display.
 Press the [ENTER] button, the display starts blinking.
 Use [DOWN] and [UP] button to select [Slave1] (normal) or [Slave2] (opposite reaction) mode.
 Once the right mode is shown on the display, press the [ENTER] button to select it.
 Press the [MENU] button for about 2 seconds to store the setting and to return to running mode.
Dimmer Curve
 Press the [MENU] button until [Dimmer Curve] is shown on the display.
 Press the [ENTER] button, the display starts blinking.
 Use [DOWN] and [UP] button to select the desired dimmer curve.
 Once the right mode is shown on the display, press the [ENTER] button to select it.
 Press the [MENU] button for about 2 seconds to store the setting and to return to running mode.
Sound State
When the sound state is switched on, the unit will work to rhythm of the beat when it is used in
standalone or master/slave mode
 Press the [MENU] button until [Sound State] is shown on the display.
 Press the [ENTER] button, the display starts blinking.
 Use [DOWN] and [UP] button to select [On] or [Off] mode.
 Once the right mode is shown on the display, press the [ENTER] button select it.
 Press the [MENU] button for about 2 seconds to store the setting and to return to running mode.
Sound Sense
Used to set the sensitivity of the internal microphone
 Press the [MENU] button until [Sound Sense] is shown on the display.
 Press the [ENTER] button, the display starts blinking.
 Use [DOWN] and [UP] button to choose a value between 0 (very low sensitivity) and 100" (high
sensitivity).
 Once the right value is shown on the display, press the [ENTER] button select it.
 Press the [MENU] button for about 2 seconds to store the setting and to return to running mode.
Blackout Mode
Blackout mode: when no DMX-signal is detected, the unit goes in blackout and waits for the DMX-
signal.
No blackout mode: when no DMX-signal is detected, the unit automatically switches to standalone
mode.
 Press the [MENU] button until [Black Out] is shown on the display.
BRITEQ
®
5/80
OPERATION MANUAL
BT-DAZZLE