Ferplast swing microchip Manual Del Usuario página 5

unless they have already been drilled when the panes are manufactured.
A Measure the belly height of your pet from the floor and position the template (side A) on
the door with the bottom at the same height.
B Mark the bottom side using a marker, you will use it as the base to center the compasses
on the points marked on the template. Then drill a circular hole with radius of 108 mm.
(The centre of the hole is marked on the template).
The biggest job is done. Go to paragraph "FIT THE FLAP".
Metal doors. Follow the same instructions as those for wooden doors. The only difference
lies in the fact that the electronic system does not work near metallic objects. It is to be
isolated using a non-metal material (wood or similar), which must have a minimum thickness
of 50 mm around the entire perimeter (Fig.5b). This prevents any interference and ensures
the correct operational efficiency of the magnetic mechanism. The biggest job is done. Go
to paragraph "FIT THE FLAP".
Walls. Follow the same instructions as those for wooden doors. (Jobs B-C-D are to be done
using suitable tools). The tunnel supplied can be installed in walls with a thickness of more
than 55 mm. In this case the tunnel must be extended in cement plastering or by purchasing
the special plastic extension (TUNNEL EXTENSION Fig.10) available as accessory for the
SWING flaps range. The biggest job is done. Go to paragraph "FIT THE FLAP".
FIT THE FLAP (Fig.5a). Position the flap on the hole and using a marker, mark the positions
where the screws are required. Remove the flap and drill 4 holes using a drill with a 4.5 mm
bit. (Warning! The 4-way locking system is to be fitted on the inner side of the door). Fit the flap
and secure it with the screws supplied, which may have to be cut and filed to remove any
sharp edges. 4 short screws are supplied for fitting to glass doors and fly screens and 4 long
screws for all other installations on a thickness of up to 55 mm. The 4 long screws will have to
be shortened for installations on an intermediary thickness (i.e.: for installations on a
thickness of 45 mm shorten the screws by 10 mm; for installations on a thickness of 35 mm
shorten the screws by 20 mm, and so on). Instead, you could purchase a new set of screws to
your specifications at your local hardware store. Too short a screw could strip the thread
whereas too long a screw could break the front panel of the pet door. To finish the job, cover
the screw holes using the plugs supplied, making sure to match the rib to the seat.
INSERT THE BATTERIES (Fig.6). When the flap is fitted you can insert the batteries in their
compartment; the flap requires n°6 1,5V AA LR6 batteries. We recommend using only good
quality alkaline batteries, in order to ensure the product efficient working. Introduce the
batteries in the correct way and wait for 10 seconds. If any microchip has not been previously
recorded the led will start flashing with cycles of 3 consecutive flashes.
Low batteries warning: a low batteries indicator will flash once every 5 seconds requiring
the replacement with new batteries.
YOUR SWING MICROCHIP FLAP IS NOW READY TO USE!
MICROCHIP RECORDING (Fig.7). To record your cat microchip press the memory button
just once, approach your cat to the flap and the code will automatically be recorded
(you'll hear the door unlocking). Since then, every time your cat gets near the flap the
device will identify him allowing the entrance. The recording time lasts 10 seconds
maximum. To record more microchips, following the instructions in the same order.
MEMORY DELETING. If you need to delete the product memory, it is sufficient to press the
memory button for 10 seconds and it will go back to the initial conditions (the led will
activate with cycles of 3 consecutive flashes).
MANUAL MODE. If you do not wish to use the electronic system, the cat flap can be
converted to work manually. To do so, press the memory button twice and the electronic
system will be excluded. By pressing again the button (just once) the product will reactivate
the electronic working keeping the previously recorded microchips.
CLEANING: QUICK AND EASY (Fig.9). The product does not require any special maintenance,
just an ordinary cleaning of the flap (A) and of the infrared detectors placed inside the tunnel
(B), at the left and right side, by using a soft and dry cloth.
The SWING MICROCHIP complies with the following requirements :
- FCC (Federal Communications Commission) Part 15
Operation is subject to the following two conditions :
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesidered operation.
Changes or modification not expressly approved by the party responsible for compliance
void the user's authority to operate the equipment.
FCC ID: 2AGP9007
WARRANTY. The pet flap SWING MICROCHIP and all its parts and accessories are covered by
warranty within the limits provided for in this paragraph and the legal regulations currently in
force. The guarantee only covers manufacturing defects and provides for free repair or
replacement. The guarantee does not cover damage and/or defects caused by carelessness,
wear and tear, usage not in accordance with the instructions and warnings in this booklet,
accidents, tampering, improper use, incorrect repairs and purchases not confirmed by receipt.
IMPORTANT. Within the European Union, a crossed-out wheelie bin symbol on the product,
documentation or packaging indicates that the product cannot be disposed of in the regular
household waste stream, in compliance with EU Directive 2012/19/EC and with current local
regulations. The product must be disposed of at recycling centres or authorised waste
disposal centres for electrical and electronic equipment, in accordance with current
legislation in the country where the product is found. Incorrect disposal of this type of waste
can have a negative impact on the environment and human health, caused by the potentially
hazardous substances produce by electrical and electronic equipment. Correct disposal of
these products will also contribute to the efficient use of natural resources. Further
information is available from the product retailer, the competent local authorities and
national manufacturer's organisations.
GB
ES
IT
FR
D
NL
PT
SK
CS
HU
SV
DA
PL
RU