Titan 8500 Instrucciones De Uso página 6

Original Operating Manual
Contents
Safety .....................................................................................6–7
Earthing Instructions ........................................................7
Service .......................................................................................7
Introduction ...............................................................................7
Using an HVLP Spray System ..............................................7-8
Setup ................................................................................7
Dual Filtration System ......................................................8
Maintenance ..............................................................................8
Cleaning/Replacing Filters ...............................................8
Replacing a Fuse .............................................................8
Troubleshooting .......................................................................9
Spare Parts List ......................................................................38
Safety
This manual contains information that must be read and understood
before using the equipment. When you come to an area that has one of
the following symbols, pay particular attention and make certain to heed
the safeguard.
This symbol indicates a potential hazard that may cause
serious injury or loss of life. Important safety information
will follow.
This symbol indicates a potential hazard to you or to the
equipment. Important information that tells how to
prevent damage to the equipment or how to avoid
causes of minor injuries will follow.
Attention
A hazard symbol such as this one refers to a specific,
task-related risk. Be sure to heed the safeguard.
i
Notes give important information which should be given
special attention.
HAZARD: EXPLOSION HAZARD DUE TO
INCOMPATIBLE MATERIALS
Will cause severe injury or property damage.
PREVENTION:
• Do not use materials containing bleach or chlorine.
• Do not use halogenated hydrocarbon solvents such
as methylene chloride and 1,1,1 - trichloroethane.
They are not compatible with aluminum and may
cause an explosion. If you are unsure of a material's
compatibility with aluminum, contact your coating's
supplier.
HAZARD: HAZARDOUS VAPORS
Paints, solvents, insecticides, and other materials
can be harmful if inhaled or come in contact with
body. Vapors can cause severe nausea, fainting, or
poisoning.
PREVENTION:
• Use a respirator or mask if vapors can be inhaled.
Read all instructions supplied with the mask to be sure
it will provide the necessary protection.
• Wear protective eyewear.
• Wear protective clothing as required by coating
manufacturer.
GB
HAZARD: EXPLOSION OR FIRE
Solvent and paint fumes can explode or ignite. Severe
injury and/or property damage can occur.
PREVENTION:
• Provide extensive exhaust and fresh air introduction
to keep the air within the spray area free from
accumulation of flammable vapors.
• Avoid all ignition sources such as static electricity
sparks, electrical appliances, flames, pilot lights, hot
objects, and sparks from connecting and disconnecting
power cords or working light switches.
• Plastic can cause static sparks. Never hang plastic
to enclose spray area. Do not use plastic drop cloths
when spraying flammable materials.
• Do not smoke in spray area.
• Fire extinguisher must be present and in good working
order.
• Power cord must be connected to a grounded circuit
PE
(electric units only).
• Follow material and solvent manufacturer's warnings
and instructions. Be familiar with the coating material's
MSDS sheet and technical information to ensure safe
use.
• Use extreme caution when using materials with a
flashpoint below 70° F (21° C). Flashpoint is the
temperature that a fluid can produce enough vapors to
ignite.
HAZARD: GENERAL
This product can cause severe injury or property
damage.
PREVENTION:
• Read all instructions and safety precautions before
operating equipment.
• Follow all appropriate local, state, and national codes
governing ventilation, fire prevention, and operation.
• Use only manufacturer authorized parts. User
assumes all risks and liabilities when using parts that
do not meet the minimum specifications and safety
devices of the pump manufacturer.
• Before each use, check all hoses for cuts, leaks,
abrasion or bulging of cover. Check for damage or
movement of couplings. Immediately replace the hose
if any of these conditions exist. Never repair a hose.
Replace it with an identical replacement hose.
• NEVER aim the gun at any part of the body.
• Wear clothing to keep paint off skin and hair.
• Do not spray outdoors on windy days.
• Never leave this equipment unattended. Keep away
from children or anyone not familiar with the operation
of HVLP equipment.
6 8500