Setting The Timer - DVA AL Serie Manual De Instrucciones

AL series
instruction
manual
gram.
ATTENTION! In order to store the data, follow the instructions
carefully. You will have to disconnect and reconnect the power
connector (fig. 9, A) and, at the same time, you will have to
press and hold down the keys next to the display.
10.1 LANGUAGE SELECTION
You can select one of the following languages: Italian, English,
French, German and Spanish.
To select your language:
- Insert the plug (fig. 9, B) in the socket
- Insert the connector (fig. 9, A) in the valve and, at the same
time, press and hold down the
see the programmed language on the display.
+
- Press the key and select your language; press
confirm.
- Disconnect the connector from the valve (fig. 9, A).
10.2 CURRENT DAY AND TIME SELECTION
– +
- Press the and keys at the same time, insert the con-
nector in the valve (fig. 9, A) until the display will show the
day of the week, flashing.
+
- Press the key and select the current day. Press
confirm.
- Using the + and – , keys, set the current time. Press
to confirm.
- Disconnect the connector from the valve (fig. 9, A).
10.3 SETTING AT WORK PROGRAM
In order to set the water softener at work, perform the fol-
lowing operations in the right order:
• - insert the power connector in the valve (fig. 9, A) and
– key until the writing "SETTING AT WORK"
press the
appears on the display.
• wait for a few seconds, then slowly open the inlet tap (fig.
3, D) first, and then slowly open the outlet tap (fig. 3, B)
At this point, the water softener, will run the installation pro-
gram by itself, carrying out the following operations:
1. backwash (B3)
2. first brine tank filling and quick wash (B7)
3. resin suction and washing (B5)
4. quick rinse and second brine tank filling (B7)
5. operation
The display will show the step performed and the residual
time until the end of the installation.
At the end of the cycle, fill the brine tank with salt for three
quarters (fig. 7); the water softener will be ready for the set-
tings. It is possible to interrupt the installation program by
pressing and holding down the
water softener will go to the "operation" step.

11) SETTING THE TIMER

When you set the timer, you can:
• set the days of the week when the regeneration will be per-
formed, or an interval of days between a regeneration and
the next.
• set the time when the regeneration will be performed
• set the water softener model
• set the possible regeneration times adjustments
• start the alarms to signal a salt shortage in the brine tank.
Before you start setting, we advise you to take note of the
model (fig. 3, L).
ATTENTION: if, during the setting, no key is pressed for more
than 1 minute, the timer display will show back the time and
day, storing the data inserted up to then.
To go back to the setting step you had reached, you need to
16
and + keys, until you
OK
to
OK
to
OK
OK
– , key for 5 seconds; the
repeat the programming from the beginning.
11.1 START
Insert the connector in the timer (fig. 9, A). The display will
show the time, the day, the water softener model (for exam-
ple, if the water softener is an AL8, the writing -08- will appe-
ar on the display).
15:00
- 08 -
11.2 SETTING THE REGENERATION DAYS
Regeneration sequences can be set weekly or according to an
interval of days between a regeneration and the next.
ATTENTION: one setting will exclude the other, so if you want
to set an interval of days between a regeneration and the next
(paragraph 11.2.2) you must not select any regeneration day
in the weekly program (paragraph 11.2.1). You will be able
to modify the settings and switch from a setting to the other
whenever you want.
1) press until the writing "PROGRAMMING: PRESS OK"
OK
appears.
2) press again. The display will show the day, flashing.
OK
11.2.1 SETTING THE REGENERATIONS ON A
WEEKLY PROGRAM
If you press + an asterisk will appear (for example *Monday),
indicating that on that day the water softener will perform a
regeneration. If you press +
ar, cancelling the regeneration.
–
If you press the key, you can scroll down the days.
Program the regenerations on the desired days and then
press .
OK
If no asterisk is placed, the timer will now allow you to set an
interval of days between a regeneration and the next (para-
graph 11.2.2).
11.2.2 SETTING THE REGENERATIONS ON AN
INTERVAL OF DAYS
If you want to set an interval of days between a regeneration
and the next, do not place any asterisk and press
writing "REGENERATION EVERY 01 DAYS".
Using the + and – keys, set the number of days between
the regenerations.
For example: if you select 12, the water softener will perform
a regeneration every 12 days.
Values go from 00 (no regeneration) to 30 (one regeneration
every 30 days).
If you set 00, the water softener will never perform an auto-
matic regeneration, but will need a manual start (see para-
graph 13.1).
After setting the number of days, press
11.3 SETTING THE REGENERATION TIME
After setting the days for the regeneration, the writing "START
REGENERAT. TIME – TIME:" will appear on the display.
1) set the regeneration time using the
press to confirm.
OK
2) set the minutes using the
confirm.
11.4 SELECTING THE WATER SOFTENER
For a correct functioning of the water softener, it is essential
that the times of the regeneration steps are set according to
ENGLISH
MONDAY
again, the asterisk will disappe-
. The
OK
to confirm.
OK
+ –
or keys and
+ or – keys and press
OK
Instruction manual AL series
to