jbc AM Serie Manual Del Usuario página 3

SPECIFICATIONS
The AM is a rework station for through-hole and
SMT boards.
- AM-2A 230V
- AM-1A 120V
It contains 4 modules which cover the main rework
tasks:
- Hot air for desoldering any size of SMD
components.
The station uses the exclusive JBC system,
based on protectors-extractors and hot-air
flow, which makes desoldering clean and quick,
concentrating the heat on the IC, and protecting
the rest of the circuit at the same time.
A medium-sized SMD can be desoldered in
less than 20 seconds.
- Desoldering SMTs and cleaning of through-
hole components and pads by using the
DR-A desoldering iron, which contains a self-
contained vacuum pump.
- Pick & Place T-260A pencil by suction to aid
components positioning.
- Soldering of all types of components, with the
swift response, power and temperature
recovery of the JBC series.
Any of the JBC tools for soldering-desoldering Any of the JBC tools for soldering-desoldering
Any of the JBC tools for soldering-desoldering Any of the JBC tools for soldering-desoldering Any of the JBC tools for soldering-desoldering
can be connected to the two modules: can be connected to the two modules: can be connected to the two modules:
can be connected to the two modules: can be connected to the two modules:
soldering handpieces, the DR-A desoldering iron,
the AP-A solder feed iron and the tweezers.
The standardization of connections allows you to
adapt your configuration in the best way to your
job's needs. Do notice that you can connect only
one desoldering iron.
The station's components
- Control unit with 1000 W heater
- T245-A handpiece
with the C245003 cartridge
- DR-A desoldering iron
with the C560003 tip
- T260-A Pick & Place
Accessories for the heater:
- JT-SA1 heater stand
- Extractor stand
- Set of 5 protectors.
- Set of 5 extractors.
- 2 tripods for the protectors.
- Set of 4 suction cups
- 3 nozzles:
ø 4
ø 6
ø 8
In order to make the nozzles removal easier, the
stand has a special bushing.
- Suction tube with connectors
Accessories for the T245-A handpiece:
- ADB-SA soldering iron stand
Accessories for the desoldering iron:
- DR-SA desoldering iron stand
- External desoldering air filter
- Spare filters
- Set of accessories
Accessories for the Pick & Place:
- Set of suction cups Pick & Place Ref. 0940163
- Set of straight needles
- Set of bent needles
- Instructions manual
The AM station has the following complementary
products:
- T210-A handpiece
- PA-A micro hot tweezers
- HT-A hot tweezers
- AP-A solder feed iron
- Pedal with cable and connector Ref. 0964551
Control unit technical specifications
the
- Maximum power soldering iron 50W
- Maximum power desoldering iron 75W
- Power heating unit 1000W
- Temperature selection of the soldering part:
from 90 to 450°C or 190 to 840°F (±5%)
- Temperature selection hot air:
from 150 to 450°C or 300 to 850ºF (±5%)
- Air flow regulation: 6-45 l/min
- Self-contained vacuum pump for holding ICs
- Station's maximum power: 1150W
- ESD protected housing.
Typical surface resistance: 10
square
- Complies with CE standards on electrical
safety,
antistatic protection.
Ref. 0008748
- RoHS compliant.
- Equipotential connector and the tool tip are
connected to station mains ground supply for
ESD protection.
Ref. 0930110
- Weight of complete unit: 19.8 kg
Ref. 0932015
Ref. 0932012
Ref. 0932020
2
electromagnetic compatibility and
This product should not be thrown in the
garbage.
ENGLISH
Ref. 0932330
Ref. 0821830
Ref. 0781046
Ref. 0009131
Ref. 0901546
Ref. 0861660
Ref. 0009055
5 -10 11 Ohms/