Tabla de contenido
Publicidad
Enlaces rápidos
MODEL SW
THIS MANUAL CONTAINS THE OPERATING
INSTRUCTIONS AND SAFETY INFORMA-
TION FOR YOUR SCAG MOWER. READING
THIS MANUAL CAN PROVIDE YOU WITH
ASSISTANCE IN MAINTENANCE AND AD-
JUSTMENT PROCEDURES TO KEEP YOUR
MOWER PERFORMING TO MAXIMUM EFFI-
CIENCY. THE SPECIFIC MODELS THAT THIS
BOOK COVERS ARE CONTAINED ON THE
INSIDE COVER. BEFORE OPERATING YOUR
MACHINE, PLEASE READ ALL THE INFOR-
MATION ENCLOSED.
© 2003
SCAG POWER EQUIPMENT
DIVISION OF METALCRAFT OF MAYVILLE, INC.
PART NO. 03130
PRINTED 7/03
PRINTED IN USA
Publicidad
Tabla de contenido
Resumen de contenidos para Scag SW Serie
- Página 1 MODEL SW THIS MANUAL CONTAINS THE OPERATING INSTRUCTIONS AND SAFETY INFORMA- TION FOR YOUR SCAG MOWER. READING THIS MANUAL CAN PROVIDE YOU WITH ASSISTANCE IN MAINTENANCE AND AD- JUSTMENT PROCEDURES TO KEEP YOUR MOWER PERFORMING TO MAXIMUM EFFI- CIENCY. THE SPECIFIC MODELS THAT THIS BOOK COVERS ARE CONTAINED ON THE INSIDE COVER.
- Página 2 WARNING: FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY. * Keep all shields in place, especially the grass discharge chute. * Before performing any maintenance or service, stop the machine and remove the spark plug wire and ignition key. * If a mechanism becomes clogged, stop the engine before cleaning.
-
Página 3: Tabla De Contenido
TABLE OF CONTENTS MODEL SW SUBJECT PAGE Introduction ....................1 General Safety Instructions ................. 1 Signal Words ....................1 Symbols ....................... 2-3 Before Operating ..................4 While Operating ................... 4 Maintenance and Storage ................5 Initial Run-In Procedures ................6 Mower Operation .................. -
Página 4: Subject
TABLE OF CONTENTS (CONTINUED) SUBJECT PAGE Illustrated Parts List Notes........................17 SWM-32", 36" Cutter Decks..............18-19 SWM-48", 52" Cutter Decks..............20-21 Notes........................22 Caster Assembly....................23 Engine Deck - 13KH, 15KH, 15KA, 17KA, 18HN........24-25 Engine Deck - 18KH................... 26-27 Handle Assembly..................28-29 Instrument Panel....................30 Peerless Transmission..................31 Engine Deck Wire Harness................32 Handle Wire Harness..................32... -
Página 5: Introduction
We encourage you to contact your dealer for repairs. following signal words to attract your attention to safety All Scag dealers are informed of the latest methods to messages found on the decals and throughout this service this equipment and provide prompt and efficient manual. -
Página 6: Symbols
ISO Symbols CE Mark SYMBOL DESCRIPTION SYMBOL DESCRIPTION Choke Transmission Parking Brake Spinning Blade 48071S On/Start Spring Tension on Idler Off/Stop WARNING Falling Hazard FALLING HAZARD USE ONLY SCAG APPROVED RIDING ATTACHMENTS SEE OPERATOR'S MANUAL 481109... - Página 7 SYMBOL DESCRIPTION SYMBOL DESCRIPTION Fast Slow Cutting element - Basic symbol Continuously variable - Linear Pinch Point Cutting element - Engage 481039S Hourmeter/elapsed operating hours Cutting element - Disengage Keep bystanders away Read operator's manual...
-
Página 8: Before Operating
Scag optional grass catcher or mulching plate are properly installed. If the dis- 8. Fill the fuel tank with clean, fresh gasoline, with a charge area should plug, shut the engine off and wait minimum octane rating of 87. -
Página 9: Maintenance And Storage
9. Always park the mower and/or start the engine on a 15. Use only Scag approved attachments and accessories. level surface. Scag Approved Attachments: GC-F4 10. If the cutting blades should strike a solid object or GC-4D the equipment should start to vibrate abnormally,... -
Página 10: Initial Run-In Procedures
8. Allow the engine to cool before storing the mower in MOWER OPERATION any enclosure such as a garage or storage shed. 1. Read and understand the safety instructions Make sure the fuel tank is empty if the machine is to before attempting to operate this machine. -
Página 11: Cutter Deck Belt Adjustments
END OF L-SHAPED -NOTE- BRACKET BELT When PTO is engaged or (possibly) disengaged, "J" BOLT a squealing sound from the underside of the machine is normal. It is caused by the electric clutch plates meshing as the cutter blades come up to speed. -
Página 12: Transmission Drive Belt
TRANSMISSION DRIVE BELT CUTTER DECK ADJUSTMENTS Adjust the transmission drive belt so that there is about a Due to the many cutting conditions that exist, it is difficult 3/16" deflection with 10 lbs. of pressure. Adjust by to suggest a cutter deck setting that will work for every loosening idler pulley mounting bolt and sliding the idler lawn. -
Página 13: Blade Height Adjustments
If blades are out of balance, vibra- tion and premature wear of spindle assembly can X Must NOT Exceed occur. See your authorized Scag dealer for 1/3 Blade Width SGB033 blade balancing or special tools if you choose to balance your own blades. -
Página 14: Custom-Cut Baffle Adjustment
Custom-Cut Baffle Adjustment 2. Move the Custom-Cut Baffle to desired position. The Custom-Cut Baffle is designed to deliver optimum airflow and superior cutting performance in any type of (See Figures 10 through 12 for position) grass. The Custom-Cut Baffle can be raised or lowered to precisely tailor the deck's performance for the type of 3. -
Página 15: Lubrication & Maintenance
Chassis grease Grease transmission couplers Chassis grease Grease idler bracket LH & RH Chassis grease Check all hardware for proper tightness More often if needed Adjust air gap on electric clutch Contact your Scag dealer for information about making this adjustment... -
Página 16: Troubleshooting Cutting Conditions
TROUBLESHOOTING CUTTING CONDITIONS CAUSE CURE CONDITION Stringers - Occasional Low engine RPM Run engine at full 3600 RPM Blades of Uncut Grass Ground speed too fast Slow speed to adjust for conditions Wet grass Cut grass after it has dried out Dull blades, incorrect sharpening Sharpen blades Deck plugged, grass accumulation Clean underside of deck... - Página 17 Deck plugged, grass accumulation Clean underside of deck Too much blade angle (deck pitch) Adjust pitch and level Deck mounted improperly See your authorized SCAG dealer Bent spindle area See your authorized SCAG dealer Dull blade Sharpen blade Width of Deck...
- Página 18 Adjust pitch and level Ridge in Center of Cutting Path Bent blade Replace blade Internal spindle failure See your authorized SCAG dealer Mounting of spindle incorrect See your authorized SCAG dealer Width of Deck SGB024 Slope Cut - Sloping Bent spindle mounting area...
-
Página 19: Technical Specifications
TECHNICAL SPECIFICATIONS MODELS SW32-13KH, SW36A-13KH, SW36A-15KA, SW36A-15KH, SW48A-15KA, SW48A-15KH, SW48A-17KA, SW48A-18HN, SW52A-17KA, SW52A-18KH, SW52A-18HN ENGINE General Type: Heavy duty industrial/commercial Brand / Model: Kawasaki FH451V & FH500V: Kohler CV13T, CV15T, CV493T Honda GXV610QAF Horsepower: Kawasaki FH451V=15HP, FH500V=17HP Kohler CV13T=13HP, CV15T=15 HP, CV493T=18HP Honda GXV610QAF=18HP Type: Kawasaki 15 HP &... - Página 20 TECHNICAL SPECIFICATIONS (CON'T) DRIVE SYSTEM Type: Belt drive with twin power belts for increased friction to pulley surface. Transmissions: Peerless 5-speed transmission, Model #700-070A. Steering/Travel Control: Clutch/brake fingertip steering, key lock switch. (EZ Grip design allows minimum hand force to operate controls.) Brakes: 6"...
-
Página 21: Notes
NOTES... -
Página 22: Swm-32", 36" Cutter Decks
32" & 36A" CUTTER DECKS SW-SWZ04CD36A... - Página 23 32" & 36A" CUTTER DECKS Ref. Part Ref. Part No. Number Description 32 36A No. Number Description 32 36A 461551 Cutter Deck (Includes Decals) 48100-02 Bronze Bearing 461634 Cutter Deck (Includes Decals) 04050-05 Retaining Ring, 1-1/8" Ext. ”E” 461663 Cutter Spindle Assy. 44078 J-Hook 43312...
-
Página 24: Swm-48", 52" Cutter Decks
48A, 52A" CUTTER DECKS 41, 41A 40 39 SW-SWZ04CD48, 52"... - Página 25 48A, 52A" CUTTER DECKS Ref. Part Ref. Part No. No. Description 48A 52A No. No. Description 48A 52A 461636 Cutter Deck (Includes decals) 04112-05 Nut, 1/2-13 Spiralock 04041-08 Flat Washer 3/4" Special 461643 Cutter Deck (Includes decals) 41A 04041-08S Flat Washer 3/4" Special 461663 Spindle Assembly 44078...
-
Página 26: Notes
NOTES... -
Página 27: Caster Assembly
CASTER ASSEMBLY SW-SWZ2003CSTR Ref. Part Description 04066-01 Quick Pin 43037-01 Spacer, Caster Yoke, 1/2" Long 48100-01 Bronze Bearing 48114-04 Grease Fitting 46082 Support Assembly (Includes Items (3 & 4) 45006 Caster Yoke 04021-07 Elastic Stop Nut, 1/2-13 43022 Sleeve, Caster Wheel Bearing 04001-37 Hex Hd. -
Página 28: Engine Deck - 13Kh, 15Kh, 15Ka, 17Ka, 18Hn
ENGINE DECK 15 KA 17 KA ONLY (1 loc.) 18 HN ONLY 40, 40A SW2004ED... - Página 29 ENGINE DECK Ref. Part Ref. Part 13KH 15KA 18HN 13KH 15KA 18HN No. No. Description No. No. Description 15KH 17KA 15KH 17KA 482852 Engine,13HP Kohler 04030-05 Lock Washer, 7/16" 32A 04102-04 Bolt, 7/16-20 x2-1/2" Hex Head (CV13T, Spec PS-21538) 32B 04103-03 Cpsrw, M10-1.5 x55 Metric Hex Hd 482853 Engine,15HP Kohler...
- Página 30 ENGINE DECK SW52A - 18KH (x3) (1 loc.) 37, 37A SW18KHED...
- Página 31 ENGINE DECK SW52 - 18KH Ref. Part Ref. Part Description Description 04102-04 Bolt, 7/16-20 x2-1/2" Hex Head 482854 Engine,18HP Kohler 04001-12 Bolt, 5/16-18 x 1-3/4" Hex Head (CV493T, Spec PS-27526) 04021-09 Nut, 3/8-16 Elastic Stop 48030-09 Cable Clamp 04040-15 Flat Washer, 5/16" 481580 Transmission, 5-speed 04017-19...
-
Página 32: Handle Assembly
HANDLE ASSEMBLY SW 2004 HA... - Página 33 HANDLE ASSEMBLY Ref. Part Ref. Part 13KH 18KH 15KA 18HN 13KH 18KH 15KA 18HN No. No Description No. No Description 15KH 17KA 15KH 17KA 04001-17 Bolt, 5/16-18 x 2" Hex Head 461597 Handle Assembly 04019-02 Nut, 1/4-20 Serrated Flange 421360 Belt Guard 04040-15 Flatwasher, 5/16 (.375 x .875 x .083) 04017-27...
-
Página 34: Instrument Panel
INSTRUMENT PANEL SW99IP Ref. Part 13KH 18KH 15KA 18HN Description 15KH 17KA 48717 Switch, Neutral Interlock 482814 Throttle Control 48946 Throttle Control 481687 Engagement Switch, Electric Clutch 48609 Key Switch (Includes hardware) 48023 Hour Meter (dealer installed) Screw, #10-32 x .50 Phillips Washer Head 04019-01 Nut, #10-32 Serrated Flange Hex Head 482711 Handle Wire Harness, Manual Start... -
Página 35: Peerless Transmission
PEERLESS 700-070 FOR REFERENCE ONLY ORDER PARTS FROM PEERLESS / TECUMSEH REF. PART Ref. Part DESCRIPTION No. No. Description 778125 Spur Rear (35 teeth) 772083A Case, Transmisson 778239A Spur Gear (32 teeth-steel) 780086A Needle Bearing Grease Spec 778124A Spur Gear (30 teeth) 780142 Needle Bearing 778123A... -
Página 36: Engine Deck Wire Harness
ENGINE DECK BLADE CLUTCH WIRE HARNESS KOHLER (18 HP) NEUTRAL KAWASAKI (15 HP & 17 HP) INTERLOCK GROUND HONDA (18 HP) WHITE BLACK W/RED STRIPE PART NO. 482683 BLACK BLACK BLUE WHITE WHITE YELLOW WIRE HARNESS ADAPTER - ENGINE INSTRUMENT SW04WH482683 PANEL HARNESS HANDLE WIRE HARNESS... -
Página 37: Wire Harness Adapter-Honda (18 Hp)
WIRE HARNESS GROUND ADAPTER HONDA (18 HP) ENGINE STATOR PART NO. 482848 BLACK RECTIFIER CAPACITOR YELLOW YELLOW WHITE MAGNETO SW04WH482848 MAIN WIRE HARNESS WIRE HARNESS ADAPTER KAWASAKI (15 HP & 17 HP) PART NO. 481717 SW2003WH481717... -
Página 38: Replacement Decals
482284 CHOKE FAST SLOW 481122 48314 32" - 48315 36" - 482297 48" - 481953 52" - 481954 482286 482816 CUTTING HEIGHT ADJUSTMENT DECK MOUNTING HOLE POSITION 48404 NUMBER OF CASTER SPACERS (BELOW SUPPORT) 48404 NUMBER OF SPACERS ABOVE CUTTER BLADES 1-7/8 2-3/8 2-1/8... - Página 39 INSTALL BELT COVER BEFORE OPERATING MACHINE READ OPERATOR'S MANUAL 481039 481039 WARNING WARNING DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCH MASTER, MULCH PLATE, OR ENTIRE GRASS CATCHER INSTALLED 482165 WARNING FALLING HAZARD USE ONLY SCAG APPROVED RIDING ATTACHMENTS SEE OPERATOR'S MANUAL 481109 481109...
- Página 40 The expense of delivering the mower to the dealer for warranty work and the expense of returning it to the owner after repair will be paid for by the owner. Scag’s responsibility is limited to making the required repairs and no claim of breach of warranty shall be cause for cancellation or rescission of the contract of sale of any Scag mower.