Craftsman 580.752140 Instrucciones De Uso página 18

. Usea vacuumcleanerto pick up loose dirt and debris.
NOTICE
j lmproper treatment of pressure washer can damage it and
_horten_ ....
its life.
DONOT insert anyobjectstbroughcoolingslots.
Check and Clean inlet Screen
Examine garden hose inlet screen. Clean if it is clogged or
replace if it is torn.
Check High Pressure Hese
High pressure hoses can develop leaks from wear, kinking,
or abuse, inspect hose before each use. @eck for cuts,
leaks, abrasions, buiging of cover, or damage or movement
of coupiings. If any of these conditions exist, replace hose
immediately.
1 A wA G
pressure stream
_ossibte
1
Dutation,
NEVERrepair high pressure hose. Replaceit.
Replacement hose rating MUST exceed maximurn pressure
ratir_gof unit.
Check Gen and Hezzle Extensien
Examine hose connection to spray gun and make sure it is
secure. Test trigger by pressing it and making sure it springs
back into piace when you releaseit. Put safety iatch in UP
position and test trigger. You should not be abie to press
trigger. Replacespray gun immediately if it fails any of these
tests.
Hezzle Maintenance
A pulsing sensation felt while squeezingthe spray gun trigger
may be caused by excessive pump pressure. The principai
cause of excessive pump pressure is a nozzle clogged or
restricted with foreign materials, such as dirt, etc. To correct
the problem, immediately clean the nozzle following these
instructions:
1. Shut off engine and turn off water supply.
2. ALWAYSpoint spray gun in a safe direction and squeeze
trigger to releaseretained high water pressure.
WARNING
The high pressure stream of water that this
equipment produces can cut through skin and its
_ nderlying tissues, ieading to serious injury and
possible amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected,
which can cause injury.
o Keephigh pressurehosecormected to pumpand spraygun
whilesystemis pressurized.
• ALWAYS pointspraygun in safedirection,pressred button
and squeeze spraygun trigger,to rebasehigh pressure, e very
tirne youstop engine.
3. Remove nozzlefrom end of nozzle extension.
4. Use a smaii paper clip to free any foreign material
clogging or restricting nozzie (A).
5. Remove nozzleextension from spray gun.
6. Using a garden hose, remove additionai debris by back
flushing water through nozzteextension. Back flush
between 30 to 60 seconds.
.
8.
9.
10.
11.
Reinstaii nozzle into nozzle extension.
Reconnect nozzle extension to spray gun.
Make sure garden hose is connected to water inlet.
Checkthat high pressure hose is connected to spray gun
and pump. Turn on water.
Start engine foiiowing instructions How to Start Your
Pressure Washe,<
Test pressure washer by operating with each quick
connect nozzb.
@-Hing Maintenance
Purchasean O-Ring RepairKit at your iocai Searsor by caiiing
1-800-4-MY-NO_IE(469°4663) or online at www.sears.com, it
is not includedwith the pressurewasher.This kit includes
repiacemento=rings,rubber washerand water inletfiiter. Referto
the instructionsheet providedin the kit to serviceyour unit's
o-fings.
WARNING
The high pressure stream of water that this
equipment produces can cut through skin and its
underiying tissues, ieading to serious injury and
}ossibb amputation.
o NEVER repairleakingconnections witb sealant o f anykind.
Replace o-ring or seal.
Pump Oil Maintenance
DO NOTattempt any oii maintenance on this pump. This
modei does not require any pump oii maintenance. The pump
is pre=iubricatedand seaiedfrom the factory, requiring no
additional lubrication for the life of the pump.
18