Batteries Disposal; Connection Battery Connector And Switching On Of The Machine; Batteries Charge Level; Hourmeter - Diamond 85 Instrucciones De Uso Y Mantenimiento

In order not to cause permanent damages to the
batteries, it is necessary to avoid their complete
discharge, providing for the recharging within a
few minutes after that the batteries discharge
signal starts blinking.
NOTE: Never leave the batteries completely
discharged even if the machine is not used. In case
of traditional batteries, please check the electrolyte
level every 20 recharging cycles and eventually top
them up with distilled water. Never leave the
batteries discharged for more than two weeks.
Danger of gas exhalations and emission of
corrosive liquids. Fire danger: do not approach
with free flames.

BATTERIES DISPOSAL

It is compulsory to hand over exhausted batteries,
classified as dangerous waste, to an authorized
institution according to the current laws.
CONNECTION BATTERY CONNECTOR
SWITCHING ON OF THE MACHINE
Once that the battery recharging has been
completed:
1. Disconnect the connector of the battery
recharger from the battery connector (1).
2. Connect then the battery connector (1) to the
machine connector (2).
To start any function of the machine, it is necessary
to rotate clockwise the key switch (5). Rotating it
counterclockwise any function will be switched off.

BATTERIES CHARGE LEVEL

When the machine is switched on, on the display
(1) appear in order the following information:
1. the version (for example A003) of software
installed on the machine.
2. the setting of the battery check card which can
be:
GE 36: check card set for GEL batteries.
or
Pb 36: check card set for lead batteries.
3. The batteries charge level indicator is digital and
remains fixed on the display. The battery charge
level starts from 100, which indicates the 100%
of the total charge and decreases from 10 to 10.
When the charge level reaches 20%, the display
starts blinking, so you are about the end of
working.
After a few seconds of the indication 10% and
after this, the blinking of the four lines, all the
functions stop automatically. With the remaining
charge it is anyhow possible to finish the drying
operation before proceeding to the recharge.

HOURMETER

The machine is equipped with an hour meter
located on the same display (1) of the battery
charge level indicator. Pressing the button (2), the
first data indicates the working hours and after a
few seconds the working minutes are shown.

SQUEEGEE ASSEMBLY

1. Insert the two stud bolts (2) situated on the
upper part of the squeegee (3) inside the slots
present on the support (1).
2. To block the squeegee tighten the stud bolts (2).
3. Insert the squeegee hose (4) into its coupling,
respecting its position as indicated in the figure.
AND

ADJUSTMENT OF THE SQUEEGEE

In order to have a perfect drying result through the
squeegee, the rear rubber must have the lower
bending uniformly adjusted in all its length. For the
adjustment, it is necessary to put oneself in
working condition and therefore the suction motor
has to be switched on and the brushes have to
function together with the detergent solution.
The lower part of the rubber is too much bent
Take off the pressure rotating the wing nut (5)
counterclockwise.
The lower part of the rubber is not much bent
Increase the pressure rotating the wing nut (5)
clockwise. Check that the wheels which adjust the
height do not rest on the floor, in this case adjust
them as indicated
adjustment".
The bending is not uniform
Adjust the squeegee
counterclockwise the wing nut (6) to increase the
bending in the central part, or clockwise to increase
the bending on the extremities.
Height adjustment
Once that the pressure and inclination of the
squeegee have been adjusted, it is necessary to fix
this optimum condition making touch slightly the
wheels onto the floor. Rotate clockwise the
registers (7) to
counterclockwise to raise them. Both wheels must
be adjusted in the same measure. To act upon the
register (7) loosen at the same time the two milled
ring nuts, adjust the height acting on the upper one
and then fix the adjustment screwing and blocking
the lower one.
Every type of floor requires a specific adjustment.
For example, concrete floors (where the friction
results to be high) need little pressure, while
smooth floors (ceramics) need higher pressure.
If the cleaning operations are made always on the
same type of floor, the adjustment can change only
in function of the rubber wear.

SPLASH GUARD ASSEMBLY

(version 85)
The two splash guards have to be assembled onto
the brushes base group.
1. Insert the metal strip inside the suitable slots
present on the rubber.
in paragraph "Height
inclination rotating
lower the wheels or
17
2. Place the round hole at the flat extremity of the
strip onto the pin (1) placed in the rear part of
the brushes base group. Secure the strip through
the nut blocking it.
3. Block the lever closing (2) placed in the front
part of the brushes base group after having
engaged the eyelet placed at the free extremity
of the metal strip.
Please act as above for both splash guard rubbers.
With the brushes assembled, the splash guard must
slightly touch the floor.
For the disassembly it is necessary to proceed
inversely with above-mentioned operation.
(version 100)
The two slash guards are already preassembled on
the two metal covers. To assemble the covers, it is
necessary to proceed as follows:
1. Take off the clips (1) present on the pins (2) fixed
to the brushes base.
2. Assemble the cover onto the brushes base.
3. Reposition the clips (1) to block.
For the disassembly it is necessary to proceed
inversely with above-mentioned operation.

BRUSHES ASSEMBLY

To assemble the brushes it is necessary that the
brushes base is in the lifted position. If it is not
lifted, proceed as follows:
Without the operator seated, turning the key
switch clockwise, the display comes on and after 3
seconds all working groups come off automatically
and are lifted from the floor.
With the brushes base group in lifted position,
insert the brushes into their plate seat underneath
the brushes base turning them until the three metal
buttons are properly seated in their slots; rotate
energically the brushes to push the button towards
the coupling spring until they get blocked.
The figure shows the rotating sense for brushes
coupling.