Oil And Fuel Information; Mixing Ratio; Assembly Instructions - Craftsman WEEDWACKER Manual Del Usaurio

OIL AND FUEL MIXING INSTRUCTIONS
Old and/or improperly mixed fuel are the main reasons for the unit
not running properly. Be sure to use fresh, clean unleaded fuel.
Follow the instructions carefully for the proper fuel/oil mixture.
Definition of Blended Fuels
Today's fuels are often a blend of gasoline and oxygenates
such as ethanol, methanol, or MTBE (ether). Alcohol-blended
fuel absorbs water. As little as 1% water in the fuel can make
fuel and oil separate. It forms acids when stored. When using
alcohol-blended fuel, use fresh fuel (less than 60 days old).
Using Blended Fuels
If you choose to use a blended fuel, or its use is unavoidable,
follow recommended precautions:
• Always use the fresh fuel mix explained in your operator's manual
• Always agitate the fuel mix before fueling the unit
• Drain the tank and run the engine dry before storing the unit
Using Fuel Additives
The bottle of 2-cycle oil that came with your unit contains a fuel
additive which will help inhibit corrosion and minimize the
formation of gum deposits. It is recommended that you use our 2-
cycle oil with this unit. If unavailable, use a good 2-cycle oil de-
signed for air-cooled engines along with a fuel additive, such as
STA-BIL ® Gas Stabilizer or an equivalent. Add 0.8 oz. (23 ml.) of
fuel additive per gallon of fuel according to the instructions on the
container. NEVER add fuel additives directly to the unit's fuel tank.
CAUTION:
For proper engine operation and
maximum reliability, pay strict attention to the oil and
fuel mixing instructions on the 2-cycle oil container.
Using improperly mixed fuel can severely damage
the engine.
INSTALL AND ADJUST THE D-HANDLE
Install
1. Place D-handle the over the shaft housing and onto the
bottom clamp (Fig. 1). Place it a minimum of 6 inches (15.24
cm) from the end of the shaft grip.
On/Off Stop Control
Housing
Shaft Grip
Minimum 6 Inches
(15.24 cm)
D-Handle
2. Start screws with a flat-head or T-25 Torx screwdriver. Do not
tighten until handle is adjusted.
Adjust
3. While holding the unit in the operating position (Fig. 2), position
the D-handle to the location that provides you the best grip.
4. Tighten the clamp screws evenly until the D-handle is secure.
OIL & FUEL INFORMATION

ASSEMBLY INSTRUCTIONS

(4) Screws
Shaft
Bottom Clamp
Fig. 1
Thoroughly mix the proper
ratio of 2-cycle engine oil
with unleaded gasoline in
a separate fuel can. Use a
40:1 fuel/oil ratio. Do not
mix them directly in the
engine fuel tank. See the
table below for specific
gas and oil mixing ratios.
NOTE: One gallon (3.8
liters) of
unleaded
gasoline mixed
with one 3.2 oz. (95 ml.) bottle of 2-cycle oil makes a
40:1 fuel/oil ratio.
NOTE: Dispose of the old fuel/oil mix in accordance to
Federal, State and Local regulations.
WARNING:
Ignited vapors may explode. Always stop the engine
and allow it to cool before filling the fuel tank. Do not
smoke while filling the tank. Keep sparks and open
flames at a distance from the area.
WARNING:
from fuel spray. Never operate the unit without the
fuel cap securely in place.
WARNING:
outdoor area. Wipe up any spilled fuel immediately.
Avoid creating a source of ignition for spilt fuel. Do
not start the engine until fuel vapors dissipate.
INSTALL LINE TRIMMER
ATTACHMENT
NOTE: To make installation easier,
place the unit on the ground or
on a workbench.
1. Turn knob counterclockwise to
loosen coupler (Fig. 11, p. 8).
2. While firmly holding attachment,
push it straight into the coupler
until the release button snaps into
the primary hole (Fig. 12, p. 8).
NOTE: Aligning the release button
with the guide recess (Fig. 12, p.
8) will help installation.
3. Turn the knob clockwise to
tighten (Fig. 13, p. 8).
LINE TRIMMER APPLICATIONS
Cutting grass and light weeds; edging; and decorative trimming
around trees, fences, etc.
6
+
UNLEADED GAS 2-CYCLE OIL
UNLEADED GAS 2 CYCLE OIL
1 GALLON US 3.2 FL. OZ.
(3.8 LITERS) (95 ml)
1 LITER

MIXING RATIO - 40:1

Gasoline is extremely flammable.
Remove fuel cap slowly to avoid injury
Add fuel in a clean, well ventilated
Fig. 2
25 ml