Purpose Of The Machine; Assembly; Placing The Unit; Installation - Hedson Drester Boxer Double Combo Manual De Operación

PURPOSE OF THE MACHINE

The unit is intended for cleaning of air-driven spray-guns that
have been used for painting.
The unit has two separated areas for cleaning:
1. An automatic washer (item 1 illustration 1), intended for
cleaning of spray-guns with gravity fed paint-cups.
In this washer either
thinner-based solvents or water-
can be used.
based solvents
2. A sink (item 2 illustration 1), intended for manual cleaning
of air-driven spray-guns that have been used for painting
with water-based paint systems, as well as of other tools
used in connection with vehicle water-based paint-jobs like:
fi ller scrapers, paint brushes and such.
In this sink
water or water-based solvents
All other use of the unit are not allowed like:
– Emptying excess paint into the unit
– Cleaning of electric chargeable items
– Collecting of various waste
– Cleaning of textile materials
– Storing of items
– Cleaning of hands or other parts of the human body
– Cleaning of any items for food or drinks

ASSEMBLY

– First of all, check if the machine has been damaged during
the transport. Remove the packaging and check again that
the machine has not been damaged during the transport. If
so, report this immediately to the transport company.
– Fit the air-driven extractor (item 3 illustration 1) over the
fl ange of the automatic washer, and connect it to the blue
air-hose (taped on the backside of the unit) by sticking the
hose into the connector of the extractor.
– The air-line on the left side of the unit (item 4 illustration 1)
is during transport placed inside the unit. Take it out, and
fasten it with the magnet in a convenient place on the left
side. The air-line can be routed either outside the side-wall,
or through the gap between the front lid and the side wall.
This air-line is intended to blow out the spray-gun after the
cleaning procedure.
– The air-gun on the right side of the unit (item 12 illustration
1) is during transport placed inside the unit. Take it out,
and fasten it with the magnet in a convenient place on the
right side. The air-line for the air-gun can be routed either
outside the side-wall, or through the gap between the front
lid and the side wall.
This air-gun is intended to blow the spray-gun dry after the
cleaning procedure.
16025 rev 2012-02-29

PLACING THE UNIT

The DRESTER BOXER DOUBLE C2 is equipment Category 2 (ref.
ATEX-directive 94/9 EC) and may therefore be placed in loca-
tions classifi ed as Zone 1 (ref. ATEX-directive 1999/92 EC). If
the DRESTER BOXER DOUBLE C2 is installed in locations clas-
sifi ed as Zone 2 (or in unclassifi ed locations), the area within
a radius of 1 m from the DRESTER BOXER DOUBLE C2 is to be
classifi ed as Zone 1, and within a radius of an additional 1.5 m
around and 0.5 m over the unit as Zone 2 (total classifi cation:
2.5 m around the machinery and 1.5 m above it). Within this
area, all equipment such as electrical items must be approved
for the Zones described. Equipment that generates naked
fl ames or sparks (e.g. welding or grinding equipment) may not
be used in this area. Smoking is not permitted. If in any doubt,
can be used. contact the local fi re service authorities for advice.
This manual is part of the unit and must be avaliable at all
times.

INSTALLATION

Compressed air
The unit must be connected to compressed air of 7-12 bar
(110-180 psi). When in use, the unit consumes 250 litres/min
(9 cfm) of air.
The air is to be connected to the moisture trap inside the unit
(item 1 illustration 2). To access this point, remove the front
panel (item 5 illustration 1) by lifting it up-and-out. The air-line
can be led into this point via the slots on the side of the unit,
or through the open back of the unit. In either case, make sure
that the air-line do not bend the hoses or in any other way
harm the pneumatic system of the unit.
To prevent pressure drops, the air line and couplings must be
adequately dimensioned. The regulator on the unit is pre-set to
6.5 bar (100 psi). This is the optimal setting and must not be
altered.
The compressed air supplied to the unit must be clean and dry.
If it is not fi rst led through a water trap and fi lter, it may cause
damage to the pneumatic components of the unit, which will
invalidate any warranty claims.
Fit a connector to the air-line on the left side of the unit (item 4
illustration 1). This air-line is intended to blow out the spray-
gun after the cleaning procedure.
Grounding the unit
Make sure that the unit is properly grounded by using the
grounding cable (item 6 illustration 2).
ENGLISH
Ref: Illustration attachment 17025
3