Dyson Small ball Manual Del Usuario página 11

Tabla de contenido

Publicidad

Base plate reassembly
Mantenimiento del cepillo armar
EMPTYING THE CLEAR BIN
Empty as soon as the dirt reaches the level of the MAX mark – do not overfill.
Switch 'OFF' and unplug before emptying the clear bin.
To remove the cyclone and clear bin unit, press down on the red button on the
top of the carrying handle on the cyclone.
To release the dirt, press all the way down on the same red button on the top of
the carrying handle on the cyclone.
To minimize dust/allergen contact when emptying, encase the clear bin tightly in
a plastic bag and empty.
Remove the clear bin carefully from the bag.
Seal the bag tightly, dispose as normal.
To refit:
– ensure the airway in the bin base is clear of dust and dirt
– close the clear bin base so it clicks into place
– push the cyclone and clear bin unit into the main body of the machine; it will
click into place
– ensure the cyclone and clear bin unit is secure.
CLEANING THE CLEAR BIN
Remove the cyclone and clear bin (see 'Emptying the clear bin').
To separate the cyclone unit from the clear bin press the red button to open
the clear bin base. This exposes a small silver button behind the red opening
mechanism. Press the silver button (on its ribbed area) and separate the cyclone
unit from the clear bin.
Clean the clear bin with cold water only.
Do not use detergents, polishes or air fresheners to clean the clear bin.
Do not put the clear bin in a dishwasher.
Do not immerse the cyclone in water or pour water into the cyclones.
Clean the cyclone shroud with a cloth or dry brush to remove any lint and dust.
Ensure the clear bin is completely dry before replacing.
To refit:
– fit the cyclone shroud into the clear bin so that the silver button clicks
and engages
– close the clear bin base so it clicks into place
– push the cyclone and clear bin unit into the main body of the appliance; it will
click into place
– ensure the cyclone and clear bin unit is secure.
WASHING YOUR FILTERS
Your machine has two washable filters, located as shown.
Check and wash the filters regularly according to instructions to
maintain performance.
Switch 'OFF' and unplug before checking or removing the filters.
The filters may require more frequent washing if vacuuming fine dust.
Wash with cold water only. Do not use detergents.
Do not put the filters in a dishwasher, washing machine, tumble dryer, oven,
microwave or near a naked flame.
Filter A
Remove cyclone and clear bin (see 'Emptying the clear bin').
Release the catch on the front of the cyclone handle and then remove the filter.
Wash the filter with cold water only. Hold under a tap and run water through the
open end until the water runs clear. Turn upside down and tap out.
Squeeze and twist with both hands to make sure the excess water is removed.
Run water over the outside of the filter until the water runs clear.
Squeeze and twist with both hands to make sure the excess water is removed.
Stand the filter on its wide, open end to dry. Leave to dry completely for a
minimum of 24 hours.
Replace the filter into the cyclone. Swing the handle back into place. Ensure the
latch clicks to engage and is secure. Fit the cyclone and clear bin unit onto the
machine (instructions above).
Filter B
This machine has a baffle that helps to reduce noise emissions. It is important to
remove the baffle before washing the filter.
Lay the machine on its side.
To remove filter B:
– turn the blue central locking dial on the outer cover of the ball
counter-clockwise until the cover is released
– lift off the cover
clik
– turn the filter one-quarter counter-clockwise to release.
Remove the baffle by pressing down firmly on each of the release clips and
push from underneath to release filter B as shown in the "Washing your filters"
section.
To avoid damage; do not use sharp tools to remove baffle.
Wash the filter with cold water only.
Filter B should be rinsed and tapped out until the water runs clear, then tapped
out again to ensure all excess water is removed. (Tap on the plastic rim, not the
filter material.) Leave to dry completely for a minimum of 24 hours.
It is normal for the filter in the ball to turn gray in color.
To refit filter B:
– align the arrow on the baffle with the arrow on the filter, press firmly until all
three clips click into place
– refit the filter on to the ball
– secure the filter by turning it clockwise so the arrows align.
When refitting the outer cover of the ball, keep turning the central locking dial
clockwise. When it starts to click it is locked.
BLOCKAGES – THERMAL CUT-OUT
This machine is fitted with an automatically resetting thermal cut-out.
Large items may block the tools or wand inlet. If any part becomes blocked the
machine may overheat and automatically cut-out.
If this happens, follow the instructions below in 'Looking for blockages'.
LOOKING FOR BLOCKAGES
Switch 'OFF' and unplug before looking for blockages. Failure to do so could
result in personal injury.
Leave to cool down for 1-2 hours before checking the filters or for blockages.
Clear any blockage before restarting.
Look for blockages in the wand, airways and cleaner head.
To release the hose from the machine, you will need to remove the wand.
Remove the clear bin and cyclone unit. Then release the hose from the machine
by pressing the red tab on the base of the hose – you can see it from the front of
the machine.
Check for blockages in the hose.
Beware of sharp objects when checking for blockages.
To refit the hose, align the guides on the base of the hose with the channels in
the neck of the airway. Ensure the red tab faces the front of the machine. Push
the hose on. It will click into place. To refit the wand follow the instructions above
in the 'Operation' section.
To remove the base plate to access an obstruction, see 'Base plate –
disassembly/reassembly'.
To look for blockages in the front airway between the ball and the cleaner
head you will need to remove the cleaner head: see 'Base plate – disassembly/
reassembly' below on how to do this.
To look for blockages in the rear airway between the ball and the cleaner
head you will need to release the elasticated rear connection. Pull the plastic
connector towards you to release from the upper airway. To replace it, pull
it a little way out on the horizontal so that it aligns with the upper airway.
Gently release it so it pulls itself back into place.
Beware of sharp objects when checking for blockages.
Refit all parts securely before using.
Clearing blockages is not covered by your warranty.
BRUSH BAR – CLEARING OBSTRUCTIONS
If your brush bar is obstructed, it may shut 'OFF'. If this happens, you will need
to remove the blockage.
Switch 'OFF' and unplug before proceeding. Failure to do so could result in
personal injury.
Beware of sharp objects when clearing obstructions.
If you still cannot clear the obstruction, please follow the instructions below to
remove the base plate. This gives more access to the obstruction. Alternatively,
contact a Dyson expert on the Dyson Helpline or visit the website. Clearing
brush bar obstructions is not covered by your warranty.
11

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Cinetic big ball

Tabla de contenido