Publicidad
Idiomas disponibles
Idiomas disponibles
attention Plumbers: tYPical mounting instructions For Pre-rinse assemblY
KL/KN50, 51, 52
FAUCET BODY
WASHER
TIGHTEN
LOCKNUT
LOCKNUT
AGAINST
DECK
YOKE
3/8"
1/2" WATER SUPPLY
TAILPIECE
LINE/NIPPLE
KL/KN56/,60, 57, 61, 58, 62
FAUCET
TIGHTEN
BODY
COUPLING NUT
TIGHTEN FLANGE
AGAINST DECK
1/2" WATER SUPPLY
MOUNTING KIT INCLUDES:
LINE/NIPPLE
Rubber Washer, Steel Washers,
Flange, Nipple and Locknut
KL/KN69, 70, 76
KL/KN71, 72
TIGHTEN FLANGE
FAUCET BODY
AGAINST SINK/
BACKLSPLASH
SINK/
BACKSPLASH
FLANGE
WASHER
FLANGE
1/2" WATER
SUPPLY
TIGHTEN
1/2" WATER
LINE/NIPPLE
FLANGE
SUPPLY LINE/
AGAINST SINK/
NIPPLE
BACKSPLASH
MOUNTING KIT IS INCLUDED
GENERAL INSTRUCTIONS:
Thank you for purchasing one of our quality plumbing products. Most faucets are supplied with mounting hardware,
including ½" nipples. For installation instructions, we will assume that hot and cold water supplies end in ½" nipples.
We recommend using a 1-1/4" hole in the deck or backsplash to accommodate the ½" supply nipples. For added
convenience it is suggested that Encore Mounting Kit (KN40-1000) be utilized with the KN53/KN54 Series fixtures.
Refer to instructions.
1. Turn off water supply at main source.
2. Hand-tighten all parts prior to tightening with wrench.
3. Do not force parts together.
4. All plated surfaces should be handled with care, avoid scratching with tools.
5. Use Teflon tape or pipe joint compound when making threaded connections to water supply lines.
ASSEMBLE COUPLING TO SINK DECK
Apply Teflon Tape or Pipe Joint Compound to the supply line nipples. Place nipple through holes in deck.
Assemble flange of each coupling to one nipple, then the other. Thread flange loosely against wall or backsplash.
ASSEMBLE FAUCET TO COUPLINGS
Carefully orient, mount and hand tighten the faucet to the two couplings. Be sure to include the washers provided.
Use wrench to tighten flange against wall or backsplash. (Maintain alignment of faucet to sink while tightening.)
Wrench-tighten couplings to faucet body. Tighten flange against sink/backsplash.
KL/KN63, 64
FAUCET BODY
WASHER
SINK/BACKSPLASH
FLANGE
1/2" WATER SUPPLY
LINE/NIPPLE
TIGHTEN
FLANGE AGAINST
SINK/BACKSPLASH
KL/KN53, 54
SINK/BACKSPLASH
WASHER
1/2" WATER SUPPLY
FAUCET
LINE/90˚ NIPPLE
BODY
MTG. KIT*
1
TIGHTEN
COUPLING
FLANGE
NUT
2
TIGHTEN FLANGE
AGAINST SINK/
BACKSPLASH
*SHOWN WITH OPTIONAL 90˚
MOUNTING KIT NO. KN40-1000
KL/KN73, 74
FAUCET
SINK/
BACKSPLASH
DECK
WASHER
FLANGE
TIGHTEN
FLANGE
LOCK NUT
AGAINST
DECK
FAUCET
1/2" WATER
BODY
SUPPLY LINE/
NIPPLE
1/2"
WASHER
COMPRESSION
NUT
1.
PRE-RINSE ASSEMBLY
LESS ADD-ON FAUCET
Apply pipe joint compound or teflon
tape to threads on both ends of riser pipe.
Thread riser pipe into faucet body and
hand tighten.
RISER PIPE
TEFLON TAPE OR PIPE
JOINT COMPOUND
FAUCET BODY
3.
ASSEMBLE WALL BRACKET
Model No. K50-Y020
Determine correct length of support rod from
wall to riser pipe. Cut rod to approximate
size. Affix wall bracket base securely to wall.
Install compression nut and bracket ferrule
and tighten securely.
WALL
BRACKET BASE
FERRULE
SUPPORT
ROD
SPRING
RETAINER
COMPRESSION
NUT
RISER PIPE
BODY
CAUTION! MANUFACTURER RECOMMENDS THE
USE OF WALL BRACKET ASSEMBLY TO SECURE
RISER PIPE ON ALL PRE-RINSE ASSEMBLIES
NOTE: WALL BRACKET SHOULD BE LOCATED
TOWARD TOP OF RISER PIPE... AS CLOSE AS
POSSIBLE TO SPRING RETAINER
5.
ASSEMBLE PRE-RINSE WITH SWIVEL ARM
a. Follow instructions above
(#1) and (#1A) connecting
WALL
BRACKET
riser pipe to faucet body.
#K50-Y020
b. Secure swivel arm spout
to riser pipe and tighten.
c. Install wall bracket
#K50-Y020. Refer to
RISER PIPE
assembly instruction
(#3) above.
FAUCET
BODY
CAUTION! MANUFACTURER RECOMMENDS
THE USE OF WALL BRACKET ASSEMBLY TO
SECURE RISER PIPE ON ALL PRE-RINSE
ASSEMBLIES.
NOTE: WALL BRACKET SHOULD BE LOCATED
TOWARD TOP OF RISER PIPE ... AS CLOSE AS
POSSIBLE TO SPRING RETAINER.
1A.
PRE-RINSE ASSEMBLY WITH
ADD-ON FAUCET
a. Apply pipe joint compound or
teflon tape to threads on end
RISER PIPE
of short riser pipe attached to
add-on faucet, thread riser pipe
into faucet body and tighten.
ADD-ON FAUCET
b. Apply pipe joint compound or
teflon tape to threads on both
ends of riser pipe, thread
riser pipe into add-on faucet
body and hand tighten.
SHORT RISER PIPE
FAUCET BODY
4.
ASSEMBLE PRE-RINSE WITH GOOSENECK SPRING
a. Assemble spring retainer to riser pipe and
tighten with wrench. This will also tighten riser
pipe on faucet body.
b. Assemble hose to spring retainer. Ensure
O-ring is in place inside of hose coupling prior
to assembly. (Refer to drawing #1 below).
Additional O-rings are provided for future use.
Tighten securely.
c. Assemble large coil spring over hose and
onto spring retainer. IMPORTANT: Spring
must be assembled vertically with large curve
of spring to the top.
d. Assemble spray head ring over spray head
grip, and assemble spray head assembly to
hose. Tighten securly. Ensure O-ring is in
place prior to assembling.
(Refer to drawing #2 below).
Note: Additional O-rings are provided in a
RETAINER
plastic bag. Realign spray head hook on
riser and tighten. Tighten all wall bracket screws.
Turn on water and check for leaks.
BE SURE O-RING IS INSTALLED
FOR PROPER PERFORMANCE
(Extra O-rings are provided)
1
2
GRIP
HOSE
COUPLING
6.
ASSEMBLE (OPTIONAL) SWIVEL ARM SUPPORT BRACKET
a. Measure and mark 8-5/16" from inside
elbow toward swivel arm spout (see detail).
b. Tighten support clamp on swivel arm
support at the point marked above.
SWIVEL
ARM SPOUT
c. Tighten screw in support clamp onto
support bracket pipe.
d. Position bottom of support bracket pipe
onto riser pipe and tighten screws (2)
on riser rotator around support bracket
SPRAY
HEAD
pipe and riser (it will be loose around the
HOSE
riser pipe).
ASSEMBLY
e. Slide riser bushing around riser pipe
and into riser rotator.
f. Assemble riser clamp around riser with
screws (2). Slide up to meet bottom of
bushing. Push up until spout is level.
Tighten all screws securely.
®
By Component Hardware
2.
ASSEMBLE SPRAY HEAD
HOOK TO RISER
Spread (open) clamp section of hook
so that it will slide over riser without marking
finish of riser. Orient spray head hook
with hook up and assemble to riser.
Place approximately half
way down length of riser.
Do not tighten at
RISER PIPE
this time.
SPRAY HEAD
HOOK
CLAMP
c
LARGE COIL
NEW
SPRING
INTEGRAL
POSITIVE SEAL
O-RING
CONSTRUCTION
ELIMINATES NEED
HOSE
FOR WASHERS
SPRAY
HEAD RING
STRAIN
RELIEF
SPRING
SPRAY HEAD
b
HOSE
GRIP
COUPLING
a
SPRING
WRONG
RIGHT
DIRECTION
DIRECTION
SUPPORT CLAMP
ELBOW
SWIVEL
ARM SPOUT
RISER ROTATOR
SUPPORT
BRACKET PIPE
RISER BUSHING
RISER CLAMP
RISER PIPE
8-5/16"
RISER CLAMP
DETAIL
Publicidad
