Dip Switch Configuration; Important Information And Maintenance - AERMEC Omnia ULI 16 C Manual De Instrucciones E Instalación

DIP SWITCH CONFIGURATION

The board has specific configuration dip-switches for the possible installations. There are 8 microswitches are and they have the fol-
lowing functions:
Dip_Board Position
Dip1
Dip2
Dip3
Dip4
Dip5
Dip6
Dip7
Dip8
Type of Sys- 2-Pipe System with
tem Electrical Heater
Dip5 OFF
Dip6 OFF
Type of fan coil
Dip7
Dip8

IMPORTANT INFORMATION AND MAINTENANCE

WARNING: The filter must be removed from the sealed pack-
age and fitted on the unit only when it is to be used for the
first time. The electrostatic charge under normal operating
conditions runs out after about two years of opening the
sealed package, after which date the filter retains its mechani-
cal function. It is advisable to replace it with a new, electro-
statically pre-charged filter available through our technical
assistance centres.
WARNING: the fan coil is connected to power supply and
water circuit. Operations performed by persons without the
required technical skills can lead to personal injury to the
operator or damage to the unit and surrounding objects.
POWER THE FAN COIL ONLY WITH 230V, SINGLE-PHASE
VOLTAGE
Any other type of power supply could permanently damage the
fan coil.
DO NOT USE THE FAN COIL IMPROPERLY
Do not use the fan coil for animal husbandry applications (e.g.
incubation).
AIR THE ROOM
Periodically air the room in which the fan coil has been installed.
This is particularly important if the room is occupied by many
people, or if gas appliances or sources of odours are present.
ADJUST TEMPERATURE ADEQUATELY
The room temperature should be regulated in order to provide
maximum comfort to the people in the room, especially if they
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
4-pipe system
ON
OFF
Meaning
With shut-off valve
No shut-off valve
Water probe upstream of the 3-way valve
Water probe down-line of the 3-way valve
Dead band 2°C
Dead band 5°C
MS input with change season function
MS input with fan coil enable function
See Table 2
(Type of system)
See Table 3
(Type of fan coil)
2-Pipe System with Plasma Clus-
ter/Bactericide lamp
OFF
ON
ULI16C
ON
OFF
are elderly, children or ill, avoiding temperature differences
above 7°C in summer between the outside and inside.
In summer, a temperature that is too low causes higher electri-
cal consumption.
CORRECTLY ADJUST THE AIR JET
The air coming out of the fan coil must not impact directly on
people; in fact, even if the air is warmer than the room temper-
ature, it could cause a cold sensation and result in discomfort.
DO NOT USE EXCESSIVELY HOT WATER
Clean the fan coil with a soft cloth or sponge soaked in water
not over 40°C. Do not use chemical products or solvents to
clean any part of the fan coil. Do not spray water on the outer
or inner surfaces of the fan coil (this might cause short circuits).
CLEAN THE FILTER PERIODICALLY
Cleaning the filter frequently guarantees enhanced operating
efficiency.
Check whether the filter is very dirty: in this case, clean it more often.
Clean frequently; remove the accumulated dust with a vacuum
cleaner.
Once the filter is clean, refit it on the fan coil following the
removal instructions but in reverse order.
SUPPLEMENTARY CLEANING
The fact that the blades of examinable shrouds can be removed
(operation done only by adequately skilled technicians) ensures
a thorough cleaning of the internal components, which is par-
ticularly important when installing the unit in crowded areas or
venues requiring high hygiene standards.
2-pipe system Cold Only + Electric resistor
(2T+2F)
ON
ON
ULI26C ULI36C
OFF
OFF
15