Publicidad
Idiomas disponibles
Idiomas disponibles
lock the buttons on the remote control. With the ex-
ception of the buttons of the user socket (15), the
floor lighting (16) and the night light (17), which are
accessible at all times. In order to lock the keys, you
hold down the memory button (14) for about 8 to 10
seconds.
A beep will be heard from the receiver. The key lock is
then activated. From now, if other buttons are pressed,
the receiver will emit 3 beeps (indicating that the re-
mote control is locked), but the slat-base will not move.
Deactivating the key lock
Hold down the memory button (14) for about 8 to 10
seconds. The beep emitted by the receiver indicates
that the buttons are reactivated.
Teach-in procedure without the simultaneous function:
1. Press both buttons (1) and (14), (SET Memory and
"all motors combined up") simultaneously and hold
it down. Then press the teach-in button (23) on the
motor control. The motor control confirms the suc-
cessfully teach-in procedure with a sound and the
background lighting on the sender blinks for a short
while. 2. The device is functional 1 sec. after the teach-
in procedure.
Teach-in procedure with the simultaneous function:
The motor control which is to operate a radio remote
control on which the ("SYN ON/OFF") simultaneous
function has not been taught needs to be assigned
as "Master". The other motor control need to be as-
signed as "Slave". The next steps are to be as follow:
1. First teach-in the master. Press both buttons (1)
and (14) simultaneously and hold it down. Then press
the teach-in button (23) on the motor control of bed 1.
The motor control confirms the successfully teach-in
procedure with a sound and the background lighting
on the sender blinks for a short while. 2. After a pause
of about 1 sec., teach-in the slave. Hold both buttons
(14) and (2) pressed and press the teach-in button
(23) on the slave motor control of bed 2. The motor
control confirms the successfully teach-in procedure
with a sound and the background lighting on the sen-
der blinks for a short while. 3. Repeat the process with
the second radio remote control, but ex-changing the
bed number. (Assign the master to bed 2 and the slave
to bed 1). 4. After a short pause (about 1 sec.) check
the teach-in procedure with both radio remote control.
Also check the simultaneous function.
Night light (LED light)
The night light (accessory floor lighting) can be activa-
ted by pressing one time the button (17).
After 30 minutes it will be automatically switched off,
or by pressing again on the button (17).
14
Operating instructions
Adjustment options
g The various sections can be adjusted using the
function buttons (3 –10) on the radio remote control.
The sleep and sit positions (position 11 – 13) have
been pre-programmed in the factory. However, you
can adjust and redefine each of these positions.
To programme your preferred positions
g Individually adjust the position with the function but-
tons (3 – 10).
g Press the memory button (14) 3 times
g Press the memory button you want to use once:
Memory position 1 – 3.
Once the electronics have recognised the newly saved
position, a sequence of sounds will confirm your
choice. The programming of a new position automati-
cally overwrites an old position. If an unchanged posi-
tion is programmed under the same memory button, a
low humming tone will sound.
To call up a position stored in memory
g Press the relevant memory button Memory position 1 –
3 until all sections have reached the required final position.
Selecting the standard pre-programmed positions
g Press the memory button 1, 2 or 3 on the radio remote
control until the sleep surface reaches the programmed
end position. The final position has been reached when
the motors can no longer be heard. The standard pre-
programmed positions can be changed and individually
adjusted (see "Programming your preferred position").
Resetting all adjustments (horizontal position)
g Press "all motors combined" button "down" (2) until
all comfort areas have reached the horizontal position
and the motors have stopped. In the case of a power
failure, the basic position can only be reached by using
the emergency lowering function.
Additional functions
Connecting a second slat base
g Use the synchronisation cable to connect the second
remote control to the first one. The synchronisation
cable for the additional remote control is available
from your Swissflex stockist.
Optional user socket
g The optional user socket is available as an accessory
from your Swissflex stockist. The optional user socket can
be used to connect an electronic device (radio, lamp) that
can be switched on and off using the radio remote control.
Care and Maintenance
Your uni 10_95RF is a high-quality product that has
been designed to serve you reliably for many years
GB
Publicidad
