Chamberlain LiftMaster Professional LM800A Manual De Instrucciones página 14

21
INSTALL DOOR CONTROL
Locate door control where the garage door is visible, away from
door and door hardware and out of the reach of children. Mount at
least 1,5 m (5 feet) above the floor.
Serious personal injury from a moving garage door may result
from misuse of opener. Do not allow children to operate the door
control or remote control transmitter.
Fasten the caution label permanently to the wall near the door
control as a reminder of safe operating procedures.
There are 2 screw terminals (1) on the back of the door control (2).
Strip about 6mm (1/4") of insulation from bell wire (4). Separate wires
enough to connect the white/red wire to RED terminal screw 1 and the
white wire to WHT terminal screw 2.
Fasten the door control to an inside garage wall with sheet metal
screws (3) provided. Drill 4mm (5/32") holes and use anchors if
installing into drywall. A convenient place is beside the service door
and out of reach of children.
Run the bell wire up the wall and across the ceiling to the garage door
opener. Use insulated staples to secure wire. The receiver quick con-
nect terminals are located behind the light lens of the opener. Connect
the bell wire to the terminals as follows: white/red to red and white to
white (5).
Operation of the Door Control
Press to open or close the door. Press again to stop the door while
moving.
PROGRAM YOUR OPENER &
22
REMOTE/WIRELESS WALL CONTROL
Activate the opener only when door is in full view, free of
obstruction and properly adjusted. No one should enter or leave
garage while door is in motion. Do not allow children to operate
push button(s) or remote(s). Do not allow children to play near
the door.
Your garage door opener receiver and remote control transmitter are
set to a matching code. If you purchase additional remote controls,
the garage door opener must be programmed to accept the new
remote code.
Program the Receiver to Match Additional Remote Control
Codes:
Using the orange "LEARN" Button:
1. Press and release the orange "learn" button on the opener. The
learn indicator light will glow steadily for 30 seconds (1).
2. Within 30 seconds, press and hold the button on the hand-held
remote that you wish to operate your garage door (2).
3. Release the button when the opener light blinks. It has learned the
code. If the light bulb is not installed, two clicks will be heard (3).
Using the Multi-Function Door Control:
1. Press and hold the button on the hand-held remote that you wish
to operate your garage door (4).
2. While holding the remote button, press and hold the LIGHT button
on the Multi-Function Door
Control (5).
3. Continue holding both buttons while you press the push bar on the
Multi-Function Door Control (all three buttons are held) (6).
4. Release buttons when the opener light blinks. It has learned the
code. If the light bulb is not installed, two clicks will be heard (7).
Now the opener will operate when the remote control push button is
pressed. If you release the remote control push button before the
opener light flashes, the opener has not learned the code.
To Erase all Remote Control Codes:
To deactivate any unwanted remote, first erase all codes: Press and
hold the orange "learn" button on opener until the learn indicator light
goes out (approximately 6 seconds). All previous codes are now
erased. Reprogram each remote or keyless entry you wish to use.
3-Channel Remote:
If provided with your garage door opener, the large button is factory
programmed to operate it. Additional buttons on any rolling code 3-
channel remote or
mini-remote can be programmed to operate this or other rolling code
garage door openers.
23
OPEN/CLOSE/STOP OPERATION
(only if you have a Multifunction door control)
Your remote control can be programmed to operate one door using all
3 buttons: the left button will only open the door, the middle button will
only close the door, and the third button will stop the door's movement.
You may set up this feature as follows:
1. With the door closed, press and hold the left remote push button.
2. Press and hold the Lock button on the door control.
3. Press and hold the door control push bar.
When the opener lights flash, release all buttons. Test by pressing the
left (Open) button on the remote. The door should open. Press it again
while the door is open and nothing should happen. Press the middle
(Close) button and the door should close. Press the third (Stop) button
while the door is moving and it should stop immediately.
24
PROGRAM YOUR KEYLESS ENTRY
Activate the opener only when door is in full view, free of obstruc-
tion and properly adjusted. No one should enter or leave garage
while door is in motion. Do not allow children to operate push but-
ton(s) or remote(s). Do not allow children to play near the door.
NOTE: Your new Keyless Entry must be programmed to operate your
garage door opener.
Program the Receiver to Match Additional Remote Control Code
Using the orange "LEARN" Button:
1. Press and release the orange "learn" button (1) on opener. The learn
indicator light will glow steadily for 30 seconds.
2. Within 30 seconds, enter a four digit personal identification number
(PIN) of your choice on the keypad (2), then press and hold the
ENTER button.
3. Release the button when the opener light blinks (3). It has learned
the code. If the light bulb is not installed, two clicks will be heard.
Using the Multi-Function Door Control:
NOTE: This method requires two people if the Keyless Entry is already
mounted outside the garage.
4. Enter a four digit personal identification number (PIN) of your choice
on the keypad, then press and hold ENTER.
5. While holding the ENTER button, press and hold the LIGHT button
on the Multi-Function Door Control.
6. Continue holding the ENTER and LIGHT buttons while you press
the push bar on the Multi-Function Door Control (all three buttons
are held).
7. Release buttons when the opener light blinks. It has learned the
code. If the light bulb is not installed, two clicks will be heard.
25
USING THE WALL-MOUNTED DOOR CONTROL
THE MULTI-FUNCTION DOOR CONTROL
Press the push bar (1) to open or close the door. Press again to stop
the door.
Light feature
Press the light button to turn the opener light on or off. It will not control
the opener lights when the door is in motion. If you turn it on and then
activate the opener, the light will remain on for 2 1/2 minutes. Press
again to turn it off sooner. The 2 1/2 minute interval can be changed to
1-1/2, 3-1/2 or 4-1/2 minutes as follows: Press and hold the Lock but-
ton until the light blinks(about 10 seconds). A single blink indicates that
the timer is reset to 1-1/2 minutes. Repeat the procedure and the light
will blink twice, resetting the timer to 2-1/2 minutes. Repeat again for 3-
1/2 minute interval, etc., up to a maximum of four blinks and 4-1/2 min-
utes.
Lock feature
Designed to prevent operation of the door from hand-held remote con-
trols. However, the door will open and close from the Door Control, the
Outside Keylock and the Keyless Entry Accessories.
To activate, press and hold the Lock button (3) for 2 seconds. The push
bar light will flash as long as the Lock feature is on.
To turn off, press and hold the Lock button again for 2 seconds. The
push bar light will stop flashing. The Lock feature will also turn off
whenever the "LEARN" button on the opener panel is activated.