Stanley STGS9115 Manual De Instrucciones página 28

ENGLISH (
Original Instructions)
Allow the tool to stop rotating before laying it down.
Precautions to take when sanding paint
• Sanding of lead based paint is NOT RECOMMENDED
due to the difficulty of controlling the contaminated dust.
The greatest danger of lead poisoning is to children and
pregnant women.
• Since it is difficult to identify whether or not a paint
contains lead without a chemical analysis, we
recommend the following precautions when sanding
any paint.
Helpful Hints
• Hold your angle grinder with one hand on the body and
the other hand firmly around the side handle as shown
in Fig. F.
• Always position the guard so that as much of the
exposed disc as possible is pointing away from you.
ff Be prepared for a stream of sparks when the disc
touches the metal.
• Maintain an angle between the disc and work surface
(Fig.J) of approximately 30° when grinding and 10°-
15° when sanding (Fig. K) for best tool control, material
removal, and minimal loading.
CAUTION! Use extra care when grinding into a corner
as a sudden, sharp movement of the grinder may be
experienced when the wheel contacts a secondary surface.
WARNING: Always wear eye protection while
operating this power tool.
Cutting metal
When cutting, work with moderate feed, adapted to the
material being cut. Do not exert pressure onto the cutting
disc, tilt or oscillate the machine.
Do not reduce the speed of running down cutting discs by
applying sideward pressure.
The machine must always work in an upgrinding motion.
Otherwise, the danger exists of it being pushed uncontrolled
out of the cut.
When cutting profiles and square bar, it is best to start at the
smallest cross section.
MAINTENANCE
Your STANLEY tool has been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning.
WARNING! To minimize the danger of serious
personal injury, please switch off the tool power
and disconnect all plugs before adjusting or
removing/ installing any accessory. Before
reassembling the tool, press and release the
trigger switch to make sure the tool is already
switched off.
WARNING! Before performing any maintenance
on corded/ cordless power tools:
28
Lubrication
STANLEY tools are properly lubricated at the factory and
are ready for use.
Tools should be lubricated regularly every year depending
on usage. (Tools used on heavy duty jobs and tools
exposed to heat may require more frequent lubrication.)
This lubrication should be attempted only by trained power
tool repairperson's such as those at STANLEY service
centers or in other qualified service personnel.
Cleaning
WARNING! Dust and grit from metal grinding
often accumulate on interior surfaces and could
create an electrical shock hazard if not cleaned
out. Use only mild soap and a damp cloth to
clean the tool. Never let any liquid get inside
the tool; never immerse any part of the tool into
a liquid.
WARNING! Never use solvents or harsh
chemicals to clean non-metal parts of the tool.
These chemicals may weaken the material of
the parts. Use only mild soap and damp cloth
to clean the tool. Never let any liquid get inside
the tool; never immerse any part of the tool into
liquid.
WARNING! Do not overload your angle grinder.
Overloading causes a reduction in speed and
efficiency, causing your angle grinder to become
too hot. If this happens, operate your angle
grinder under no load for one or two minutes until
it has cooled to normal operating temperature.
Switching your angle grinder off under load will
reduce the life of the switch.
IMPORTANT! To ensure product SAFETY
and RELIABILITY, repairs, maintenance and
adjustment (other than those listed in this
manual) should be performed by authorized
service centers or other qualified organizations,
always using identical replacement parts. Unit
contains no user service able parts inside.
ACCESSORIES
WARNING: Since accessories, other than those
offered by STANLEY, have not been tested with
this product, use of such accessories with this
tool could be hazardous. To reduce the risk of injury, only
STANLEY, recommended accessories should be used with
this product.
The performance of any power tool is dependent upon the
accessory used. STANLEY accessories are engineered to
high quality standards and are designed to enhance the
performance of power tool. By using STANLEY accessories
will ensure that you get the very best from your STANLEY
tool. STANLEY offers a large selection of accessories
available at our local dealer or authorized service center at
extra cost.