Electric Dryers; Electrical Requirements - KENMORE ELITE 796.6142 Manual De Uso Y Cuidado

ELECTRIC DRYERS
ELECTRICAL REQUIREMENTS
WARNING: To he p p revent fir°,
electrical shock, serious injury, or death, the wiring
and grounding must conform to the latest edition of
the National Electrical Code, ANSIiNFPA 70 and all
applicable local regulations. Please contact a qualified
electrician to check your home's wiring and fuses to
ensure that your home has adequate electrical power to
operate the dryer.
Electricat
No es
A WARNING: To reduce the .sk of
fire,
electric shock, or injury to persons when using this
appliance, follow basic precautions, including the
following:
* Any installation in a manufactured or mobile
home must comply with the Manufactured Home
Construction and Safety Standards Title 24 CFR, Pars
32=80 or Standard CAN/CSA0Z240 MH and local
codes and ordinances.
*A 4-wire connection is required for all mobile and
manufactured home instoHaflons, as well as aft new
constru_ion offer January |, |996. Failure to do so
can result in fire, explosion, or death.
"A gas dryer must be permanently attached to the floor.
* To reduce the risk of combustion and fire, the dryer
must be vented to the outside.
- DO NOT vent the dryer under a manufactured home or
mobile home.
"Electric dryers may be vented to the outside using the
back, left, right, or bottom panel.
* Gas dryers may be vented to the outside using the
back, left, or bottom panel. Gas dryers may not be
vented to ;he outside using the right side panel because
of the burner housing.
"The dryer exhaust duct must be aff3xed securely to
the manufactured or mobile home structure, and the
exhaust duct must be made of a material that will resist
fire and combustion, it is recommended that you use a
rigid or flexible metal duct.
- DO NOT connect the dryer exhaust duct to any other
duct, vent, chimney, or other exhaust duct.
. Make sure the dryer has adequate access to outside
fresh air to ensure proper operation. The opening for
outside fresh air must be at least 25 in2 (163 cm2).
"rt is important that the clearance of the duct from any
combustible construction be at least 2 inches (5 cm),
and when venting the dryer to the outdoors, the dryer
can be installed with a clearance of 1 inch (2.5 cm) at
the sides and back of the dryer.
"Please be aware that venting materials are not supplied
with the dryer. You should obtain the venting materials
necessary for proper installation.
WARNING: To reduce the.sk of
tire, electric shock, or injury to persons when using this
appliance, follow basic precautions, including
the following:
• This dryer must be connected to a grounded metal,
permanent wiring system, or an equipment grounding
concluder must be run with the clrculf conductors and
connected to the equipment grounding terminal or
lead on the dryer. Failure to do so can result in fire,
explosion, or death.
The dryer has its own terminal block that must be
connected to a separate 240 VAC, 60-Hertz, single
phase circuit, fused at 30 amperes (the circuit must be
fused on both sides of the line). ELECTRICAL SERVICE
FOR THE DRYER SHOULD BE OF THE MAXIMUM
PATE VOLTAGE LISTED ON THE NAMEPLATE. DO
NOT CONNECT DRYER TO 110=, 115-, OR |20-VOLT
CIRCUIT. Failure to follow these instructionscan result
in fire, explosion, or death.
- if branch circuit to dryer is 15 ft. (4.5 m) or less in
length, use UL (Underwriters Laboratories) listed No.=
10 AWG wire (copper wire only), or as required by
local codes, ff over 15 ft. (4.50 m), use UL=listed No.-8
AWG wire (copper wire only), or as required by local
codes. Allow sufficient slack in wiring so dryer can
be moved from its normal location when necessary.
Failure to do so can result in fire, explosion, or death.
o The power cord (pigtail) connection between wall
receptacle and dryer terminal block IS NOT supplied
with the dryer. Type of pigtail and gauge of wire
must conform to local codes and wlfh instrudions on
fee following pages. Failure to follow these instructions
can result in fire, explosion, or death
* A 4=wire connection is required for all new
construction after January 1, |996. A 4-wlre
connection must be used where local codes do not
permit grounding through the neutral wire. Failure to
do so con result in fire, explosion, or death.
12