Maintenance Instructions - Sunex Tools 6605B Instrucciones De Operación

ASSEMBLY INSTRUCTIONS:
. This unit comes pre-assembled, except for the handle.
2. Unscrew bolt from handle block assembly. Hold handle
parallel with ground, slide into handle block assembly.
Screw the bolt back in.
3. Check all bolts for tightness before use.
IMPORTANT! BEFORE USE:
Air may become trapped in the hydraulic system during
transit. To purge air:
. Open release valve by pulling handle lever to the right.
2. Pump foot pedal rapidly 4 full strokes. This will expel air
that may have entered oil passages during transit.
3. Close release valve by pulling handle lever to the left.
4. If lift arm raises, jack is ready for use. If not, repeat
this procedure.
OPERATING INSTRUCTIONS:
IMPORTANT: Before attempting to raise a vehicle, check
vehicle service manual for recommended lifting surfaces.
1. To raise load: Close release valve tightly by pulling handle
lever to the left. Position jack under load so that saddle
will contact load firmly and load is centered so it cannot
slip. Operate footpedal until saddle approaches the load.
Then unlock the handle by pulling the handle lever up and
to the right. Pump the handle to lift the load. Once again
check to see that the saddle is correctly positioned. Place
jack stands of appropriate capacity under the vehicle.
DO NOT CRAWL UNDER VEHICLE WHILE LIFTING
VEHICLE OR PLACING OR REMOVING JACK
STANDS! Place jack stands at vehicle manufacturer's
recommended lift areas that provide stable support for the
raised vehicle.
2. To lower load: Slowly push handle lever down and to the
right to lower the vehicle onto the jack stands. When
release valve is opened, saddle and load will be lowered.
Lower the vehicle slowly so as not to shock load the jack
stands. Once repairs are completed, raise vehicle enough
to remove jack stands.
CAUTION: Keep hands or feet away from the hinge
mechanism of the jack.

MAINTENANCE INSTRUCTIONS:

All moving joints require lubrication often. Remove handle
and grease the lower end of handle where it strikes the
release mechanism. Using a grease gun, grease the lift arm
pivot shaft grease fitting until grease appears at the end
of the shaft. Oil all lift arm linkages, front wheels and rear
casters.
OWNER/USER RESPONSIBILITY:
The owner and/or user must have a thorough understanding
of the manufacturer's operating instructions and warnings
before using the Service Jack. Personnel involved in the use
and operation of equipment shall be careful, competent,
trained, and qualified in the safe operation of the equipment
and its proper use when servicing motor vehicles and their
components. Warning information should be emphasized
and understood. If the operator is not fluent in English, the
6605B
6605B_manual_071107.indd 4
manufacturer's instructions and warnings shall be read to
and discussed with the operator in the operator's native
language by the purchaser/owner, making sure that the
operator comprehends its contents.
Owner and/or user must study and maintain for future
reference the manufacturer's instructions and pertinent
warning information. Owner and/or user is responsible for
keeping all warning labels and instruction manuals legible
and intact. Replacement labels and literature are available
from the manufacturer.
LIMITED WARRANTY:
SUNEX INTERNATIONAL, INC. WARRANTS TO
ITS CUSTOMERS THAT THE COMPANY'S SUNEX
TOOLS BRANDED PRODUCTS ARE FREE FROM
®
DEFECTS IN WORKMANSHIP AND MATERIALS.
Sunex International, Inc. will repair or replace its Sunex
Tools branded products which fail to give satisfactory
®
service due to defective workmanship or materials, based
upon the terms and conditions of the following described
warranty plans attributed to that specific product.
This product carries a ONE-YEAR warranty. During this
warranty period, Sunex Tools
option any part or unit which proves to be defective in
material or workmanship.
Other important warranty information...
This warranty does not cover damage to equipment or
tools arising from alteration, abuse, misuse, damage and
does not cover any repairs or replacement made by anyone
other than Sunex Tools or its authorized warranty service
®
centers.
The foregoing obligation is Sunex Tools'
this or any implied warranty and under no circumstances
shall we be liable for any incidental or consequential
damages.
Note: Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
Return equipment or parts to Sunex Tools
prepaid. Be certain to include your name and address,
evidence of the purchase date, and description of the
suspected defect.
If you have any questions about warranty service, please
write to Sunex Tools . This warranty gives you specific legal
®
rights and you may also have other rights which vary from
state to state.
Repair kits and replacement parts are available for many
of Sunex Tools products regardless of whether or not the
®
product is still covered by a warranty plan.
SHIPPING ADDRESS: Sunex Tools
MAILING ADDRESS:
4
will repair or replace at our
®
sole liability under
®
, transportation
®
315 Hawkins Rd.
Travelers Rest, SC 29690
Sunex Tools
P.O. Box 4215
Greenville, SC 29608
rev. 03/0/05
7/12/07 4:34:08 PM