Sunex Tools SXC605A Instrucciones De Operación página 4

Operating Instructions • Warning Information • Parts Breakdown
Nipple
Air Supply...
Tools of this class operate on a wide range of air pressures.
It is recommended that air pressure of these tools measure
90 PSI at the tool while running free. Higher pressure and
unclean air will shorten tool life because of faster wear and
may create a hazardous condition. Water in the air line will
cause damage to the tool. Drain the air tank daily. Clean
the air inlet filter screen on at least a weekly schedule. The
recommended hookup procedure can be viewed in Figure 1.
The air inlet used for connecting air supply, has standard 1/4"
NPT American Thread. Line pressure should be increased
to compensate for unusually long air hoses (over 25 feet).
Minimum hose diameter should be 3/8" I.D. and fittings
should have the same inside dimensions.
Lubrication...
Lubricate the tool daily with a good grade of air tool oil. If no
air line oiler is used, run a teaspoon of oil through the tool.
The oil can be squirted into the tool air inlet , or into the hose
at the nearest connection to the air supply, then run the tool.
A rust inhibitive oil is acceptable for air tools.
WARNING: After an air tool has been lubricated, oil
will discharge through the exhaust port during the first few
seconds of operation. The exhaust port must be covered with a
towel before applying air pressure to prevent serious injury.
Limited Warranty...
SUNEX INTERNATIONAL,
BRANDED PRODUCTS ARE FREE FROM DEFECTS IN WORKMANSHIP AND MATERIALS.
Sunex International, Inc. will replace any SXC Series Air Tool which fails to give satisfactory service due to defective workmanship or materials.
This product carries a ONE-YEAR warranty. During this warranty period, Sunex Tools will replace free of charge any part or unit which proves to
be defective in material or workmanship.
Other important warranty information...
This warranty does not cover damage to equipment or tools arising from alteration, abuse, misuse, damage and does not cover any repairs or
replacement made by anyone other than Sunex Tools or its authorized warranty service centers.The foregoing obligation is Sunex Tools' sole liability
under this or any implied warranty and under no circumstances shall we be liable for any incidental or consequential damages.
Note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not
apply to you. Return tool to Sunex Tools, transportation prepaid. Be certain to include your name and address, evidence of the purchase date, and
description of the suspected defect.
If you have any questions about warranty service, please write to Sunex Tools. This warranty gives you specific legal rights and you may also have
other rights which vary from state to state. After the one year direct replacement warranty has expired, some service parts are available for purchase
through normal Sunex Tools service options.
Shipping Address: Sunex Tools • 315 Hawkins Rd. • Travelers Rest, SC 29690
Mailing Address: Sunex Tools • P.O. Box 4215 • Greenville, SC 29608
SXC605A
Figure 1
INC. WARRANTS
Troubleshooting...
Other factors outside the tool may cause loss of power or
erratic action. Reduced compressor output, excessive drain
on the air line, moisture or restrictions in air pipes or the use
of hose connections of improper size or poor condition may
reduce air supply. Grit or gum deposits in the tool may cut
power and may be corrected by cleaning the air strainer and
flushing out the tool with gum solvent oil or an equal mixture of
SAE #10 oil and kerosene.
Operation...
Use the enclosed wrench to assemble the disc to the tool. Let
the sander do the work. The normal weight of the machine is
sufficient for efficient sanding. Do not put additional pressure
on the machine. This will only slow down the speed of the pad,
reduce sanding efficiency and put additional burden on the
motor.
Start the work with an abrasive grit just coarse enough to
remove high spots and roughness. Follow with additional
sandings using finer grits until the desired finish is obtained.
Never go from a coarse grit to a fine grit in one step. It may
be difficult to remove swirl marks made by coarse abrasives.
Use the finest grits practical for roughing operations and finish
by using successively finer grits.
TO ITS CUSTOMERS
4
THAT THE COMPANY'S SUNEX TOOLS
®
Rev. 10/28/05