DeWalt DWE4118 Manual De Instrucciones página 30

ENglish
Proper Hand Position (Fig. G)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the mounted
side handle, with the other hand on the main handle.
Fig.G
Prior to Operation
• Install the guard and appropriate disc or wheel. Do not
use excessively worn discs or wheels.
• Be sure the inner and outer flange are
mounted correctly.
• Make sure the disc or wheel rotates in the direction of
the arrows on the accessory and the tool.
Variable Speed Dial (Fig. A)
The variable speed dial 5 offers added tool control and
enables the tool to be used at optimum conditions to suit
the accessory and material.
• Turn the variable speed dial
the dial upward for higher speed and downward for
lower speed.
Switches

CAUTION: Hold the side handle and body of the tool
firmly to maintain control of the tool at start up and
during use and until the wheel or accessory stops
rotating. Make sure the wheel has come to a complete
stop be fore laying the tool down.
NoTE: To reduce unexpected tool movement, do not
switch the tool ON or OFF while under load conditions.
Allow the grinder to run up to full speed before touching
the work surface. Lift the tool from the surface before
turning the tool off. Allow the tool to stop rotating before
putting it down.
Slider Switch (Fig. A)

WARNING: Before connecting the tool to a power
supply, be sure the slider switch is in the OFF position
by pressing the rear part of the switch and releasing.
Ensure the slider switch is in the OFF position as
described above after any interruption in power
supply to the tool, such as the activation of a ground
fault interrupter, throwing of a circuit breaker,
28
to the desired level. Turn
5
accidental unplugging, or power failure. If the slider
switch is locked ON when the power is connected, the
tool will start unexpectedly.
To start the tool, slide the ON/OFF slider switch
the front of the tool. To stop the tool, release the ON/OFF
slider switch.
For continuous operation, slide the switch toward the front
of the tool and press the forward part of the switch inward.
To stop the tool while operating in continuous mode, press
the rear part of the slider switch and release.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning.
Pop-off Brushes
The motor will be automatically shut off indicating that the
carbon brushes are nearly worn out and that the tool needs
servicing. The carbon brushes are not user-serviceable. Take
the tool to an authorised D WALT repair agent.
e
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the
risk of eye injury, always wear approved eye protection
when performing this.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Accessories

WARNING: Since accessories, other than those
offered by D WALT, have not been tested with this
e
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center.
Repairs
The charger and battery pack are not serviceable.

WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
1 toward
WALT
e