Installation And Initial Use; Electric Connection - Sammic PS-12 Manual De Instrucciones

Indications for CE marking
Each machine is identified as follows:
- Name and address of the manufacturer:
SAMMIC, S.L., C/Atxubiaga 14, Azpeitia,
Gipuzkoa (SPAIN)
- "CE" mark.
- The machine model according to the next
paragraph.
- The serial number is printed on the
Guarantee Card and in the Declaration of
Conformity
MODELS
This manual describes the PS-12, PS-22 and
PS-32 meat mincer installation, operation
and maintenance instructions.
The model reference and technical data
appear on the identification plate affixed to
the machine.
Our meat mincers are designed and
manufactured in compliance with the
following European directives
standards:
98/37/EEC Machine Directive.
73/23/EEC Low Tension Current Directive.
89/336/EEC Electromagnetic Compatibility
Directive.
EN 12331 Food processing machinery -
Mincing machines - Safety and hygiene
requirements.

INSTALLATION AND INITIAL USE

For optimum performance and long-lasting
preservation of your machine, carefully
read the installation and initial use
instructions given in this manual as well as
the recommended operation procedure.
Location
Place the mincer on a flat, horizontal and
rigid surface, making sure it is perfectly
levelled, in order to avoid vibration and
noise.
To prevent damage to your machine, never
lean it on any of its sides.

ELECTRIC CONNECTION

Motor Characteristics.
These meat mincers include a
follows:
- PS-12: Single-phase 440W.
- PS-22: Three-phase, 100 W or Single-
phase 740W.
- PS-32: Three-phase, 1.500 W.
A single-phase motor is supplied for
operation on 230V / 50Hz or on 220V /
60Hz.
A three-phase motor is supplied for
operation on 230 - 400V / 50Hz or on
220V / 60Hz.
Before connecting the mincer to the mains,
check that the motor is prepared to operate
on the actual mains voltage. If not, change
the motor voltage setting. To change from
400V to 230V on PS22/32 mincers, remove
the trough from the mincer. Change the
connection of the contactor coil and
connect the relevant terminal strip. (each
strip has a mark on it, indicating the
voltage it is designed for).
Power Cable Characteristics
The SAMMIC
complete with a thermoplastics-sheathed
power cable 1.3m in length.
THIS APPLICANCE MUST BE EARTHED. The
machine earth wire is identified.
- Single-phase mincers: prepare one 2P+E
wall outlet and plug.
- Three-phase mincers: prepare one 16A
4P+E wall outlet and a sealed plug to be
fitted to the cable of the mincer.
and
Changing the
rotation.
The direction of rotation of the unit is
anticlockwise. In order to invert the
direction of rotation on machines with a
three-phase motor,
positions of any two wires.
OPERATING CONDITIONS AND PROCEDURE
Before switching on the machine, assemble
the mincing attachment following these
instructions rigorously (see Fig. A).
- Introduce tube (1) into the motor unit, so
that the guide tongue on the tube fits into
the groove in the plastic outer collar (2).
- Turn the knob (3) situated on one side of
the appliance until it knocks against the
tube which is now blocked..
- Insert the screw (4) into the tube to a stop
and check that you cannot rotate the
screw with your hand.
Fitting of the ENTERPRISE SYSTEM blade
and grid
- Set the blade (5) on the shaft end of the
screw (4) with the cutting edge pointing
outwards.
- Put the grid (6) against the blade (5).
motor as
- Set the extra ring (9). Only for stainless
steel mincing attachment.
- Screw on the lock nut (7) over the
attachment outlet by hand.
Fitting of the UNGER SYSTEM blade and
grids, stainless steel mincing attachment
- Set the 3-hole grid (8) on the shaft end of
the screw (4) with the largest opening
facing the motor unit.
- Put the blade (5) against the 3-hole grid
(8).
mincers are delivered
motor direction of
interchange the
- Set the multi-hole grid (6) against the
blade (5).
- Mount the extra ring (9).
- Screw on the lock nut (7) over the
attachment outlet by hand.
Notes:
- Switching on the machine must be done
on no load.
- To feed meat into the mincer, always use
Ithe pusher (10) and NEVER your fingers.
- In order to avoid injuries or damage to the
blade, NEVER put your hand or any
metallic object into
attachment when the machine is on.
BUILT-IN SAFETY FEATURES
The machine incorporates the following
features that assure the user's safety:
- Size of meat feed hole according to EN
12851.
- Trough with fixed protector that makes it
impossible to introduce one's hand.
- Machine stop switch.
Important:
For safety's sake, do not use this mincer
with perforated discs having holes greater
than 8mm in diameter or discs less than
5mm thick.
MAINTENANCE (ROUTINE AND REMEDIAL)
- Before starting with the
overhaul or repair of your machine,
always unplug it from the mains.
- All the parts of this appliance that are in
contact with food must be cleaned
immediately after use with hot water and
an approved food-compatible detergent,
rinsed with plenty of hot water and dried
with a cotton cloth.
- The outside of the motor unit MAY NOT
BE cleaned under a water jet. For cleaning,
use a wet cloth and any ordinary
detergent.
- Check the venting grid for obstruction
periodically.
- The blades are sharp-edged. Handle them
with care when cleaning.
- If the power cable should get damaged, it
would be necessary to fit a new one; such
a replacement may be done only by a
SAMMIC authorised technical assistance
service.
- Sound level of the machine, in operation,
as measured at a height of 1.6m and 1m
away from the source: less than 70 dB(A).
Background noise: 32 dB(A).
the mincing
cleaning,
ENGLISH 3