Adjusting The Balance; Listening To Radio - Denon DRA-F101 Instrucciones De Operación

[2] Setting the loudness mode
Press the TONE or MODE button to display
"LOUDNESS".
TONE
MODE
1
(Main unit) (Remote control unit)
• The mode switches as shown at the left each
time the button is pressed.
"LOUDNESS" cannot be selected when the
source direct mode is on.
Either turn the FUNCTION dial on the main unit
or use the remote control unit's SELECT
buttons.
VOLUME
/SELECT
(ON)
FUNCTION
(OFF) (ON)
2
(OFF)
(Main unit) (Remote control unit)
• To set to "ON":
Turn the dial clockwise (,) or press the
button.
To set to "OFF":
Turn the dial counterclockwise (.) or press
the H button.

[3] Adjusting the balance

Press the TONE or MODE button to display
"BALANCE" (Refer to page 12.)
TONE
MODE
1
(Main unit) (Remote control unit)
"BALANCE" cannot be selected when the
source direct mode is on.
Either turn the FUNCTION dial on the main unit
or use the remote control unit's SELECT
buttons.
VOLUME
(right
/SELECT
(left channel channel
volume volume
FUNCTION
adjustment) adjustment)
(Main unit) (Remote
2 control unit)
• If the volume of the right speaker is low:
Turn the dial clockwise (,) or press the
D
button.
If the volume of the left speaker is low:
Turn the dial counterclockwise (.) or press
the button.
H
• The balance can be set to "CENTER" or
adjusted within the range of +1 to +10 in
steps of 1. When set "CENTER", the
difference between the volume of the left and
right speakers is 0.
8

LISTENING TO RADIO

(1) Tuning
MEMORY
FUNCTION
TONE TIMER DISPLAY / SET DOWN
SYSTEM
ON / STANDBY
PHONES
1
OFF ON
SYSTEM
POWER
(left channel
volume
1 2 3
adjustment)
4 5 6
7 8 9
RANDOM
(right
10 +10
channel
CD SRS
TAPE MD TIME EDIT
volume
adjustment)
DIMMER
RDS BAND TUNING
2
D
STOP PLAY VOLUME
/SELECT
Example: Tuning in FM 92.50 MHz
(AM stations are tuned in using the same procedure.)
Press the power operation switch to turn on the
power.
SYSTEM
ON / STANDBY
1
(Main unit) (Remote control unit)
Press the BAND button on the tuner to select
the FM AUTO.
BAND
2
(Main unit) (Remote control unit)
3 2
Auto Tuning
• When a program being broadcast in stereo is
received, the "STEREO" indicator lights and the
VOLUME
TUNING
SOURCE
UP BAND DIRECT
program is received in stereo.
• If reception is poor and there is much noise in the
stereo signals, press the BAND button to set the FM
MONO mode.
AM-FM STEREO RECEIVER DRA-F101
• When one of the TUNING UP/DOWN button is
pressed, the frequency changes in steps of 100 kHz
in the FM band, 10 kHz in the AM band.
• If one of the TUNING UP/DOWN button is held for
over 1 second, the frequency continues to change
1
when the button is released (auto tuning) and stops
when a station is tuned in. Tuning will not stop at
stations whose reception is poor.
PROG /
DIRECT
• To stop the auto tuning function, press the TUNING
CALL
UP/DOWN button once.
CLEAR
REPEAT
NOTE:
TIME/
PANEL
A humming sound may be heard when using a TV
nearby while receiving AM programs. If this happens,
3
move the system as far from the TV as possible.
Use the TUNING UP/DOWN button to tune the
frequency to 92.50.
TUNING
ON
DOWN UP
SYSTEM
POWER
3
(Main unit)
This lights when a station is tuned in.
BAND
ENGLISH
TUNING
(Remote control unit)
13