Checks; Disposal; Troubleshooting Guide; Pairing The Electronic Control Unit With The Radio Remote Control - Truma Mover smart A Instrucciones De Uso

Checks

– Check the installation, wiring and connections for damage
at regular intervals. The drive units must be able to move
freely, and the spring must automatically return them to
the safe idle position when they are disengaged. If this is
not the case, check the drive units for dirt or corrosion on
their guides, and have them cleaned by trained specialists if
necessary.
– After the annual inspection, check whether all motors react
properly to the commands from the remote control.
– At least every 2 years, an expert must check the Mover for
rust, check that detachable parts are firmly attached and
check that all safety-related parts are in good working order.

Disposal

The device must be disposed of in accordance with the ad-
ministrative regulations of the respective country in which it is
used. National regulations and laws must be observed.

Troubleshooting guide

Error Cause and remedy
Mover not
– Check the power supply (the green
working LED on the control unit must be
lit). Replace a defective fuse in the
battery connection cable of the
Mover only with an original Truma
spare part (part no. 60040-00169).
– Interrupt the power supply for
at least 20 seconds. Restore the
power supply. The green LED on
the control unit should be lit.
Mover not work- Control unit is overheated.
ing and red LED
on the control unit – Interrupt the power supply with
flashing the battery cut-out switch and
remove the key. Allow the con-
trol unit to cool down for at least
20 minutes. Then restart the
Mover.
Mover not re- Weak battery in the remote control
sponding to – red LEDs on the remote control
commands from
flashing.
remote control
or only with – Check the battery and battery
interruptions
contacts of the remote control. Re-
place battery and/or clean battery
contacts if necessary.
Weak Mover battery – green LED on
the control unit flashing.
– Check Mover battery. Charge or
replace battery if necessary.
Drive roller sliding
– Check tyre pressure and adjust if
off tyre necessary.
– Check tread and replace tyres if
necessary.
– Disengage Mover and measure
gap between tyre and drive roller.
The gap must be 20 mm.
EN
16
Error Cause and remedy
Mover does not – Make sure that the power sup-
engage on one
ply is not interrupted and that the
side (only Mover remote control is not switched off
smart A) during disengaging. During the
disengaging process, when the
drive rollers have completely dis-
engaged, they again move forward
a few millimetres to take the load
off the mechanics. The procedure
is completed only when the dis-
play on the remote control stops
flashing.
– Turn the socket spanner clockwise
approx. 2 revolutions to slightly
engage the Mover. Then try en-
gaging again.
Mover does not – Disengage the Mover manually.
disengage (only (see "Disengage the Mover smart
Mover smart A)
A" on page 14)
Before calling customer service, please check the
following:
– Are the batteries in the remote control in perfect condition?
– Is the remote control paired with the control unit? Carry out
the steps in "Pairing the electronic control unit with the ra-
dio remote control" on page 16.
– Is the caravan battery in perfect condition and fully
charged? Please note that battery performance can deterio-
rate considerably at cold ambient temperatures.
If these actions do not remedy the problem, please con-
tact Truma Service.
Pairing the electronic control unit with
the radio remote control
If you are using the control unit or the remote control for the
first time or if you have replaced either of these, they must be
paired with each other again in accordance with the instruc-
tions below.
Make sure that the drive rollers are not in contact with the
tyre. Check that the battery is properly connected and in good
condition, and that the control unit is being supplied with
12 V.
– Establish the power supply for the Mover via the battery
cut-off switch. Green LED lit.
– Press the reset button (Figure 12 - 1) on the remote control
with a thin object. The antenna of the control unit can be
used for this.
The green (Figure 12 - 2) and red LEDs (Figure 12 - 3) on the
remote control now flash alternately.
– Switch on the remote control. The control unit and remote
control pair automatically. Green LED lit.