Technical Data; Safety Instructions - AEG BS 12G Manual Original

TECHNICAL DATA

Drilling capacity in steel ..........................................................
Drilling capacity in wood .........................................................
Drilling capacity in brick and tile .............................................
Wood screws (without pre-drilling) ..........................................
No-load speed 1st gear ..........................................................
No-load speed 2nd gear .........................................................
Rate of percussion under load max. .......................................
Torque .....................................................................................
Battery voltage ........................................................................
Drill opening range .................................................................
Weight with battery (1.4 Ah) ...................................................
Noise/vibration information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (K = 3 dB(A)) ..........................................
Sound power level (K = 3 dB(A)) ..............................................
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined according to EN 60745.
Vibration emission value a
GB
Percussion drilling into concrete ...............................................
Uncertainty K= .........................................................................
Drilling into metal ......................................................................
Uncertainty K= .........................................................................
Screwing ..................................................................................
Uncertainty K= .........................................................................
*1 Measured according to AEG norm N 877318
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745
and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with
different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running
but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.
WARNING!
Read all safety warnings and all instructions, including those
given in the accompanying brochure. Failure to follow the warnings
and instructions may result in electric shock, fire and/or serious
injury. Save all warnings and instructions for future reference.

SAFETY INSTRUCTIONS

Wear ear protectors. Exposure to noise can cause hearing loss.
Hold power tool by insulated gripping surfaces, when performing
an operation where the fastener may contact hidden wiring.
Fasteners contacting a "live" wire may make exposed metal parts of
the power tool "live" and could give the operator an electric shock.
Always wear goggles when using the machine. It is recommended to
wear gloves, sturdy non slipping shoes and apron.
Sawdust and splinters must not be removed while the machine is
running.
When working in walls ceiling, or floor, take care to avoid electric
cables and gas or waterpipes.
Remove the battery pack before starting any work on the machine.
English
10
h
Cordless drill
BS 12G BS 14G
........10 mm ..............10 mm................ 10 mm ................... 10 mm
........30 mm ..............32 mm................ 30 mm ................... 32 mm
............ - ....................... - ...................... 6 mm ..................... 8 mm
.......4,2 mm .............4,2 mm............... 4,2 mm .................. 4,2 mm
...0-350 /min ....... 0-400 /min ..........0-350 /min .............0-400 /min
.0-1350 /min ..... 0-1400 /min ........0-1350 /min ...........0-1400 /min
............ - ....................... - ..............20 250 /min ............21 000 /min
........30 Nm ...............32 Nm ................ 30 Nm ................... 32 Nm
........12 V ...............14,4 V ................... 12 V ................... 14,4 V
.....1-10 mm .......... 1-10 mm.............1-10 mm ................1-10 mm
.....1,65 kg ..............1,95 kg ................. 1,8 kg .................... 2,1 kg
........90 dB(A) ...........90 dB(A) ............. 90 dB(A) ................ 90 dB(A)
......101 dB(A) .........101 dB(A) ........... 101 dB(A) .............. 101 dB(A)
............ - ....................... - ................. 15,6 m/s
............ - ....................... - ................... 1,5 m/s
...< 2,5 m/s ...... < 2,5 m/s
2
.......1,5 m/s ............1,5 m/s
2
...< 2,5 m/s ....... < 2,5 m/s
2
.......1,5 m/s ............1,5 m/s
2
Do not dispose of used battery packs in the household refuse or
by burning them. AEG Distributors offer to retrieve old batteries to
protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
Use only System GBS chargers for charging System GBS battery
packs. Do not use battery packs from other systems.
No metal parts must be allowed to enter the battery section of the
charger (short circuit risk).
Never break open battery packs and chargers and store only in dry
rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load
or extreme temperatures. In case of contact with battery acid wash
it off immediately with soap and water. In case of eye contact rinse
thoroughly for at least 10 minutes and immediately seek medical
attention.
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Wear a suitable dust protection mask.
Cordless impact drill
BSB 12G BSB 14G
............... 13,7 m/s
2
................. 1,5 m/s
2
.........< 2,5 m/s .............< 2,5 m/s
2 2
............. 1,5 m/s ................. 1,5 m/s
2 2
.........< 2,5 m/s .............< 2,5 m/s
2 2
............. 1,5 m/s ................. 1,5 m/s
2 2
2
2
2
2
2
2