Installation With Base; Recline Adjustment; Height Adjustment - Graco Turn2Me Manual Del Usuario

3
This child restraint is suitable for
vehicle seats with ISOFIX anchor
points.
Installation
with base
4 13
See images -
4
Fit the ISOFIX guides with the
ISOFIX anchor points.
The ISOFIX guides can protect
the surface of the vehicle seat
from being torn. They can also
guide the ISOFIX connectors.
5
After placing the base on the
vehicle seat﹐ pull the load leg
downward to floor.
6
There are 10 adjustable positions
for ISOFIX. Press the ISOFIX
adjuster button to extend the
ISOFIX.
7
Make sure that both ISOFIX
connectors are securely attached
to their ISOFIX anchor points.
The colors of the indicators on
both ISOFIX connectors should
be completely green.
If a tighter install or increased
cabin space is required﹐ then
press the ISOFIX adjuster button
6 7
-1 and push to adjust.
8
After attaching the ISOFIX﹐ pull
the load leg downward to floor.
9
When the load leg indicator
shows green﹐ the load leg is
installed correctly. Squeeze the
load leg releasing button﹐ then
adjust the load leg length.
The load leg has 12 positions.
When the load leg indicator
shows red this means the load
leg is in the wrong position.
Make sure the load leg is in full
contact with the vehicle floor
pan. Red means it is installed
incorrectly.
10
Check to make sure the base is
securely installed by pulling on
both ISOFIX connectors.
The ISOFIX connectors must be
attached and locked onto the
ISOFIX anchor points.
The load leg must be installed
correctly with green indicator.
Please refer to rear facing mode
and recline positions mode in
section to use the child restraint.
11
To remove from the vehicle
press the ISOFIX adjuster button
and pull the base back from the
seat.
12
Then press and release the
connectors from the vehicle's
ISOFIX.
14
13
To prevent damage during
transit﹐ press the ISOFIX adjuster
button and fold the connector
completely.

Recline Adjustment

14
See image
14
Squeeze the recline adjustment
button ﹐ to adjust the child
restraint to the proper position.
Please recheck the load leg
position after reclining.
There are 5 recline positions for
rear facing mode and 5 recline
positions for forward facing
mode.

Height Adjustment

for Head Support and Shoulder
Harnesses
15 17
See images -
Please adjust the head support
and check if the shoulder
harnesses are at the correct
15
height according to .
When used rear facing﹐ the
shoulder harness height must be
even with child's shoulders.
When used forward facing﹐ the
shoulder harness height must be
even with child's shoulders.
16
Squeeze the head support
adjustment lever﹐ meanwhile
pull up or push down on the
head support until it snaps into
17
one of the 6 positions.
Using in the Rear
Facing Mode
(Rearward Facing Mode/for Child
under 18kg /infant - 4 years old)
18 27
See images -
Please install the child restraint on the
rear vehicle seat﹐ and then put the
4
child in the child restraint.
18
Press the ISOFIX adjuster button
and pull the base back from the
vehicle seat.
19
Press the rotating button to
rotate for easier side loading/
unloading of the child﹐ then
rotate back to desired direction.
20
If a tighter install or increased
cabin space is required﹐ then
press the ISOFIX adjuster button
and push to adjust.
21
The ISOFIX connectors must be
attached and locked onto the
ISOFIX anchor points.
The load leg must be installed
correctly with green indicator.
After the child is placed into the seat﹐
check whether the Shoulder Harness
Straps are at proper height.
15
9
-