Product Familiarisation; Intended Use; Unpacking Your Tool; Before Use - Silvercrest 178555 Manual De Instrucciones

GB
• If the battery does not appear to be charging, or displays any unusual
operating characteristics, dispose of battery and replace
• Allow batteries to cool for 15 minutes after charging or heavy use
• Wash thoroughly with soap and water if battery acid contacts skin or
clothing
• If battery acid contacts eyes, wash thoroughly with clean water and
seek medical help
• Batteries should always be disposed of at suitable recycling facility. Do
not dispose of batteries with normal household waste
• Keep battery charger and batteries clean; foreign objects or dirt may
cause a short circuit. Failure to follow these instructions may cause
overheating or fire
• When not in use, batteries should be stored in a dry place at room
temperature (20˚C). Ensure that batteries are stored in such a way that
they cannot accidentally short-circuit in storage
• Always recycle lead acid batteries. Contact your local or national
authority for the correct recycling procedure. When returning batteries
cover the terminals with insulated adhesive tape to prevent shorting
and possible fire or explosion
• Always keep lead acid batteries out of reach of children

Product Familiarisation

1 Ammeter
2 Carry Handle
3 DC Fuse
4 Voltage Switch
5 230V Fuse
6 Charge Rate Switch
7 On/Off Switch
8 Information Panel
9 Mains cable
10 Negative Clamp (Black)
11 Positive Clamp (Red)

Intended Use

Battery charger suitable for charging conventional wet cell lead acid
batteries that are either fitted in a vehicle or free standing. 12V (normally 6
cell) and 24V (normally 12 cell) batteries are supported.

Unpacking Your Tool

• Carefully unpack and inspect your tool. Familiarise yourself with all its
features and functions
• Ensure that all parts of the tool are present and in good condition. If
any parts are missing or damaged, have such parts replaced before
attempting to use this tool

Before Use

WARNING: Do not connect the charger to the mains power supply until
instructed in the steps below.
Connecting to battery (in vehicle)
WARNING: This battery charger is not suitable for assisting engine
cranking. Do not turn on the ignition or attempt to start the vehicle with this
battery charger connected.
6
• This charger is suitable for use on 12V/24V, negative earth, vehicle
electrical systems only, when charging with the battery fitted in the
vehicle
• Marine batteries must ALWAYS be moved to dry land for charging. This
charger is not designed for use in a marine environment
• If appropriate, check battery fluid level before charging. Top up with
distilled water if required. Check battery manufacturer's guidance as to
whether cell caps should be removed for charging
• Ensure that engine is stopped, and that all electrical accessories (lights,
radio etc) are switched off. Keep vehicle bonnet, boot or access panels
open during battery charging
• Locate battery and identify battery terminals. The positive terminal
is usually marked with a '+' symbol, the negative terminal is usually
marked with a '-' symbol. If you are unsure of which terminal is which,
seek professional assistance
• Refer to vehicle manufacturer's handbook to determine whether
terminals should be disconnected for charging. Follow manufacturer's
guidance
1. If the battery terminals are corroded, or dirty, clean them with a
suitable wire brush
2. Attach Positive Clamp (Red) (11) to positive battery terminal
3. Attach Negative Clamp (Black) (10) to a clean part of the vehicle
chassis, or other sturdy metal part. Do not connect the clamp to any
part of the vehicle's fuel system.
Note: Do not connect the Negative Clamp to the negative battery terminal.
This helps prevent the risk of a spark at the battery terminal igniting
flammable gas.
4. Check that clamps are securely connected, and that they will not
loosen during charging process
5. Check the Voltage Switch (4) is set correctly and the Charge Rate
Switch (6) is set to 'MIN' then connect to the mains supply to
commence charging
Connecting to battery (free standing)
• This charger is only suitable for use with 12V and 24V lead acid (wet
cell) batteries
• If appropriate, check battery fluid level before charging. Top up with
distilled water if required. Check battery manufacturer's guidance as to
whether cell caps should be removed for charging
• Identify battery terminals. The positive terminal is usually marked with a
'+' symbol, the negative terminal is usually marked with a '-' symbol. If
you are unsure of which terminal is which, seek professional assistance
1. If the battery terminals are corroded, or dirty, clean them with a
suitable wire brush
2. Attach Positive Clamp (Red) (11) to positive battery terminal
3. Attach Negative Clamp (Black) (10) to negative battery terminal
4. Check that clamps are securely connected, and that they will not
loosen during charging process
5. Check the Voltage Switch (4) is set correctly and the Charge Rate
Switch (6) is set to 'min' then connect to the mains supply to
commence charging
Operation
Charging battery
WARNING: Only use the 'BOOST' position of the Charge Rate Switch (6)
for a short amount of time. Do not leave the battery unattended while in
'BOOST' charging mode.
WARNING: Never charge a battery where the water level is low. These will
produce a higher level of explosive/flammable gas and damage the battery.
IMPORTANT: This charger is not suitable for charging AGM, gel or other
VRLA (valve-regulated lead acid) type batteries. It is suitable for wet cell
lead acid batteries only.