General Safety Precautions; Technical Specifications; Electrical Connections; Operating Mode - DITEC COM501ES Manual De Instalación

Bluetooth LED
Spento
Acceso
Lampeggiante
Per configurazione Bluetooth vedere parametro B9 sul quadro elettronico.
i
NOTA: vedere importanti informazioni nell'ultima pagina.

GENERAL SAFETY PRECAUTIONS

This installation manual is intended for professionally competent
personnel only. Read the instructions carefully before beginning to
install the product. Incorrect installation may be a source of danger.
Packaging materials (plastic, polystyrene, etc.) must not be allo-
wed to litter the environment and must be kept out of the reach of
children for whom they may be a source of danger. Before beginning the
installation check that the product is in perfect condition. For repairs or
replacements of product only original spare parts must be used. These
instruction must be kept and forwarded to all possible future user of the
system.

1. TECHNICAL SPECIFICATIONS

Degree of protection
Temperature
2. INSTALLATION
Secure the function selector switch near the automation in a safe posi-
tion which is also suitable for use (ref. fig. 2-8).

3. ELECTRICAL CONNECTIONS

Carry out the electrical connections indicated on page 2, 3.
i
For more examples, please refer to the automation installa-
tion manual for Ditec DAS200 sliding doors.
To read the complete manual use the following QR code or type the fol-
lowing link:
https://www.ditecentrematic.com/Entrematic/ditecentrematicCOM/QR/
Multilanguages/DAS200/DitecDAS200.pdf

4. OPERATING MODE

Enabling the use of the selector.
The different operation modes are selected by pushing their respective
symbols. The present selection is indicated by a blue light.
The following functions can be selected on the control panel (MCU) for
operation mode selector key lock.
Parameter B1= 00. No access code.
Parameter B1= 01. Hold for 2s.
Access is obtained by holding any mode selection button for 2 seconds.
Parameter B1= 02. Passcode.
Passcode can be selected where the access is obtained by briefly
pushing the buttons in correct order.
The entire passcode must be entered within 10 seconds.
The passcode can be changed through the DAS900CT.
Bluetooth disabilitato
Bluetooth abilitato
Il modulo Bluetooth si sta
associando con la App Entrematic
Door Connect
IP43
-20°C / +55°C
Default passcode is
Parameter B1= 03. Key (only COM501ER)
To enable the use of the selector, rotate the key clockwise towards the
symbol .
The will light up for 15 seconds. Select the required mode.
NOTE: When B1 is set to Hold for two sec (01), the access will be locked
5 seconds after a button has been pushed.
When b1 is set to Passcode (02) or Key (03), the access will be locked
15 seconds after entering passcode or activating key, or when a new
mode selection has been confirmed.
NOTE: When B1 is set to either Passcode (02) or Key (03), the operation
mode selection must be confirmed by pressing the
In the a light can be displayed.
- A red light indicates an error.
- A yellow light every other second is indicating that maintenance is due.
- A magenta light every other second is indicating a status or con-
dition that can be cleared by the owner e.g. a break-out door is
standing open.
- A steady green light is displayed when the OMS is unlocked and B1
is configured for Passcode (02) or Key (03).
- A green light is flashing 4 times per second when a new operation
mode has been selected but not yet confirmed.
- A green light will flash whenever a button is pressed while typing
the passcode.
- A green light will be displayed for 1 second when Mode Selector
Key Impulse is given (e.g. by holding
operation mode is OFF).
SYMBOL
OPEN
The door is permanently open. The door can be moved
by hand e.g. for window cleaning. All activation units
except for the emergency push button (if fitted) are di-
sconnected.
PARTIAL
Two-way traffic, AUTOPARTIAL is obtained. The door can
be opened partially with the inner and outer activation
units and with a key switch (if fitted). With an emergency
push-button the door opens fully.
AUTO
Two-way traffic, normal operation of the door. The door
can be opened with the inner and outer activation units
and with a key switch/emergency push-button (if fitted).
EXIT
Passage from inside only. The door is normally locked
(unlocked if escape route) if an electromechanical lo-
cking device has been fitted. The door can only be ope-
nedwith the inner activation unit or with a key switch/
emergency push-button (if fitted).
CLOSE
In an escape route the OFF mode may only be set after it
is certain that all people have left the building.
The door cannot be opened with inner or outer activation
units. The door is locked if an electromechanical locking
device has been fitted.
The door can be opened partially with a key switch (if fit-
ted). The door can be opened fully with an emergency
pushbutton (if fitted).
The door can be opened partially from the operation
mode selector if
impulse is configured). This function depends on how
parameters B1 and B8 are set.
RESET
By briefly pushing the button placed in the hole accessi-
ble from the underside of the OMS with a narrow object,
the door operator will make a RESET function with a
system test. The door will then be ready for normal ope-
ration.
5
.
.
for 2 seconds when the
FUNCTION
is pushed (based on how Key
IT