Publicidad
Idiomas disponibles
Idiomas disponibles
3
CONTROLS AND INDICATORS
1. Trigger - Opens and closes the Current Clamp jaws.
2. OFF - 1m V/A - 10m V/A Switch - Turns the Current Clamp power
ON and OFF; sets the Current Clamp to the appropriate scale.
3. ZERO Adjustment Thumbwheel - Adjusts the Automotive Tester
reading to "zero" prior to making DC current measurements.
4. Power - Low Battery Indicator
■
Lights GREEN when the Current Clamp is turned ON to indi-
cate the unit is ready for use.
■
Lights RED when the Current Clamp is turned ON to indicate a
low battery condition.
4
CLAMP CURRENT MEASUREMENT
1. Plug the BLACK test lead into the 'COM' jack; plug the RED test
lead into the appropriate channel.
2. Set the tester's Function/Range Selector switch to the appropriate
position for clamp current measurements.
3. Set the Current Clamp's OFF - 1m V/A - 10m V/A switch to the
desired range. Verify the Power indicator lights GREEN.
4. If necessary, use the ZERO Adjustment Thumbwheel to "zero" the
tester reading.
5. Squeeze the trigger to open the clamp jaws. Place the clamp jaws
around the wire or cable from the source or load under measure-
ment; release the trigger.
6. Read the results on the tester's display.
LIMITED ONE YEAR WARRANTY
The Manufacturer warrants to the original purchaser that this unit is free of defects in materials and workmanship under normal use and mainte-
nance for a period of one (1) year from the date of original purchase.
If the unit fails within the one (1) year period, it will be repaired or replaced, at the Manufacturer's option, at no charge, when returned prepaid to
the Service Center with Proof of Purchase. The sales receipt may be used for this purpose. Installation labor is not covered under this warranty.
All replacement parts, whether new or remanufactured, assume as their warranty period only the remaining time of this warranty.
This warranty does not apply to damage caused by improper use, accident, abuse, improper voltage, service, fire, flood, lightning, or other acts
of God, or if the product was altered or repaired by anyone other than the Manufacturer's Service Center.
The Manufacturer, under no circumstances shall be liable for any consequential damages for breach of any written warranty of this unit. This war-
ranty gives you specific legal rights, and you may also have rights, which vary from state to state. This manual is copyrighted with all rights
reserved. No portion of this document may be copied or reproduced by any means without the express written permission of the Manufacturer.
THIS WARRANTY IS NOT TRANSFERABLE. For service, send via U.P.S. (if possible) prepaid to Manufacturer. Allow 3-4 weeks for service/repair.
SERVICE PROCEDURES
If you have any questions, require technical support or information on UPDATES and OPTIONAL ACCESSORIES, please contact your local store,
distributor or the Service Center.
USA & Canada:
(800) 544-4124 (6:00 AM-6:00 PM, 7 days a week PST)
All others: (714) 241-6802 (6:00 AM-6:00 PM, 7 days a week PST)
FAX: (714) 432-3979 (24 hr.)
Web: www.equus.com
Innova Electronics Corp.
17352 Von Karman Ave.
Irvine, CA 92614
© 2013 Innova Electronics Corp. All rights reserved
5
NOTE: A 9-volt battery is required for operation of the Current
Clamp.
1. Set the Current Clamp's OFF - 1m V/A - 10m V/A switch to the
OFF position. Disconnect the Current Clamp from the Automotive
Tester.
2. Remove the screw from the battery compartment cover. Use your
finger or a small coin to remove the cover.
3. If necessary, remove the old battery from the battery connector.
4. Match the battery terminals with the battery connector contacts,
and snap the battery connector securely onto the battery.
5. Place the battery in the battery compartment.
6. Reinstall the battery compartment cover.
WARRANTY AND SERVICING
3
2
1
REPLACING THE BATTERY
4
Publicidad
