Electrical Conection - T.I.P. DIO 45/13 flex Instrucciones Para El Manejo

When tightening threaded connections, please do not apply excessive force which may cause damage.
When laying the connection pipes, you should make sure that the pump is not exposed to any form of weight,
vibration or tension.
5.2. Installation of the pressure line
The pressure line conveys the liquids to be discharged from the pump to the point of withdrawal. To avoid
dynamic flow losses, one should use a pressure line having at least the same diameter as the pressure port (1) of
the pump.
It is recommended to use the outlet element (12) with stopcock (13) (included in the scope of delivery) and, where
needed, the riser-pipe segments (7) (also included) as a pressure line.
The flexible outlet element with the stopcock can be installed directly to the pressure port of the pump. To
increase the length of the pressure line, it is possible to insert up to three riser-pipe segments between the
pump's pressure port and the outlet element. When using more than one riser-pipe segments, they should first be
screwed to each other. Subsequently, please screw the single riser-pipe segment or the set of sub-assembled
riser-pipe segments to the pressure port of the pump. To conclude, install the outlet element with stopcock onto
the riser pipe. In this process, please use one of the enclosed sealing rings for each screwed connection.
When installing the flexible outlet element, please make sure that the uneven side of the seal is located in the
direction of the outlet and the flat side is pointing towards the pressure port or riser pipe, respectively.
5.3. How to position the pump
When positioning the pump, please make sure that the max. submersion depth indicated in the technical data will
not be exceeded. Likewise, please make sure that the minimum self-priming level is not fallen short of. If
everything is properly set, the water level may decrease down to the minimum suction level once the pump is
operating.
The pump has to be adjusted vertically and then fully immersed into the liquid to be discharged. When positioning
the pump, please ensure a sufficient distance from the bottom to prevent sand, mud or similar matters from being
sucked in.
To fasten the pump safely and securely to the rim of the container, you can use the fastening clamp (4) that
comes with the device and is to be mounted to the riser pipe. To begin, loosen and remove the wing nut of the
mounting clip (10). Then fold up the mounting clip carefully and remove the shell inside the clamp which you can
then position to the desired place on the riser pipe by simply clipping it on. Subsequently, push the mounting clip
over the thread of the riser-pipe segment and attach it on the inner shell again. Reattach the wing nut to the
mounting clip, tighten it carefully so that the fastening clamp is securely held in place. Subsequently, place the
connection cable of the pump in the cable guide of the mounting clip. To conclude, you can use the carrying
handle of the pump to lift it into a container and fasten it to the container's rim using the fastening clamp. In this
process, please make sure that the flexible part of the outlet element projects outwards beyond the rim of the
container.
To position, lift up or carry the pump, please use only the carrying handle. If required for lowering or raising the
pump, you may connect a suitable lowering rope to the carrying handle. In no case must the pressure hose, the
mains cable or the cable of the floating switch be used to position, to lift up or to carry the pump.
5.4. Functioning of the floating switch
Please make sure that the pump will cut out as soon as the water level decreases and the
floating switch has reached the cut-out level.
Also, it must be made sure that the floating switch can move freely.
The pump is equipped with a floating switch (2) causing the unit to cut in or out automatically as a function of the
water level. As soon as the water level has reached or dropped below, the cut-out level, the pump will cut out.
When the water level reaches or raises above the cut-in level, the pump will resume operation.
6. Electrical connection
The unit is equipped with a mains connection cable and a mains plug. It must only be replaced by qualified staff to
avoid any danger. Please do not use the mains connection cable to carry the pump, and do not use this cable to
pull off the plug from the socket, either. Protect the mains connection cable and mains plug from heat, oil or sharp
edges.
The values stated in the technical details have to correspond to the mains voltage. The person
responsible for the installation has to make sure that the electrical connection is earthed in
compliance with the applicable standards.
10
3