Getting Started - TFA 30.3167 Instrucciones De Uso

TFA Anl_No. 30.3167_05_17 18.05.2017 16:53 Uhr
Instruction manual
Cat.-No. 30.3167
Fig. 1
D 1
D 2
D 4
D 3
Fig. 2
Seite 2
Temperature transmitter
Thank you for choosing this instrument from TFA.
1. Before you start using it
• Please make sure to read the instruction manual carefully.
• Following and respecting the instructions in your manual will
prevent damage to your instrument and loss of your statutory
rights arising from defects due to incorrect use.
• We shall not be liable for any damage occurring as a result of
non-following of these instructions. Likewise, we take no
responsibility for any incorrect readings and for any conse-
quences which may result from them.
• Please take particular note of the safety advice!
• Please keep this instruction manual for future reference.
2. Features of the temperature transmitter
• Additional temperature transmitter for wireless weather stations
(e.g. 35.1093)
• For the wireless transmission of outdoor temperature and DCF
time (433 MHz), transmission range up to 30 m (free field)
• Also for temperature control of remote rooms, f. e. children's
room, wine-cellar
3. For your safety
• This product should only be used as described within these
instructions.
• Unauthorized repairs, modifications or changes to the product are
prohibited.
Caution!
Risk of injury:
• Keep this instrument and the batteries out of the reach of children.
• Batteries must not be thrown into a fire, short-circuited, taken
apart or recharged. Risk of explosion!
• Batteries contain harmful acids. Low batteries should be changed
as soon as possible to prevent damage caused by leaking. Never
use a combination of old and new batteries together, nor batteries
of different types.
• Wear chemical-resistant protective gloves and safety glasses
when handling leaking batteries.
Important information on product safety!
• Do not place your product near extreme temperatures, vibrations
or shocks.
D 3
• Protect it from moisture.
• The outdoor transmitter is protected against splash water, but is
not watertight. Choose a shady and dry position for the transmit-
ter.
4. Elements
D 1: Transmission indication LED
D 2: Wall mount hole
D 3: Battery compartment holders
D 4: "CH" button
5. Setting up

5.1 Getting started

• Place the display unit and the transmitter on a desk with a distance
of approximately 1.5 meter. Check that no other electronic devices
are close.
• Take the display unit into operation according to the manual of the
display unit.
• Open the battery compartment of the transmitter by pushing
inwards the two latches at the bottom and insert 2 x AA 1,5 V bat-
RoHS
teries, observing the correct polarity.
• The LED indicator of the transmitter is blinking and the transmitter
is set to channel 1 by default.
Temperature transmitter
• After the sensor is powered up, it will first transmit the temperature
and then the sensor will start radio controlled time reception. Dur-
ing the DCF time reception period (maximum 10 minutes), no
weather data will be transmitted.
• After the reception of the radio controlled time the DCF signal
appears permanently on the display of the weather station.
• Note: DO NOT PRESS ANY KEY during the first 10 minutes learning
period or before radio controlled time is displayed on the receiver.
After both outdoor values and radio controlled time are displayed
you can place your remote sensor outdoors at the final destination.
In case the clock cannot detect the DCF-signal (for example due to
disturbances, transmitting distance, etc.), the time can be set man-
ually. If the outdoor weather data is not displayed or if any key is
pressed before the weather station receives the signal, or when
changing transmitter batteries you will need to follow the battery
installation procedure again. Please wait minimum 10 seconds
before reinserting the batteries!
Note for Radio Controlled Time DCF
The time base for the radio controlled time is a Caesium Atomic
Clock operated by the Physikalisch Technische Bundesanstalt Braun-
schweig which has a time deviation of less than one second in one
million years. The time is coded and transmitted from Mainflingen
near Frankfurt via frequency signal DCF-77 (77.5 kHz) and has a
transmitting range of approximately 1,500 km. Your radio-controlled
clock receives this signal and converts it to show the precise time in
summer or wintertime. The quality of the reception depends greatly
on the geographic location. In normal cases, there should be no
reception problems within a 1,500 km radius around Frankfurt.
Please take note of the following:
• The radio controlled time receiver is built inside the thermo-sen-
sor. It is recommended to keep distance to any interfering sources
and ferro-concrete buildings.
• During night-time, the atmospheric disturbances are usually less
severe and reception is possible in most cases. A single daily
reception is adequate to keep the accuracy deviation below 1 sec-
ond.
6. Positioning of the transmitter
• Choose a shady and dry position for the transmitter. (Direct sun-
shine falsifies the measurement and continuous humidity strains
the electronic components needlessly)
• Check the transmission of 433 MHz signal from the transmitter to
the display unit (transmission range 30 m free field). Within ferro-
concrete rooms (basements, superstructures), the received signal
is naturally weakened.
• If necessary choose another position for transmitter and/or dis-
play unit.
7. Additional transmitters
• The sensor will automatically transmit temperature to the display
unit on channel 1 after batteries are inserted.
• For having more than one external transmitter, select a different
channel (1 to 3) for every transmitter by pressing the "CH" button
on the transmitter while the transmission indication LED is flash-
ing. Press twice for channel 2 and three times for channel 3 right
after the starting up of the transmitter. The LED is flashing once
for channel 1, twice for channel 2 and three times for channel 3
(channel 4 and 5 are not usable for model 35.1093).
• Press and hold the "CH" button on the display unit for 2 sec. to
start initialization manually. The channel number on the LCD of the
display unit flashes and the new transmitter will be received auto-
matically (model 35.1093).
8. Resetting
• There are chances that the receiver unit and the transmitter may
need to be reset, e.g., changing of batteries. User is suggested to:
1. Remove the batteries from each unit and wait at least 30 sec-
onds.
2. Proceed from step 1 in "Setting up"
Temperature transmitter
9. Care and maintenance
• Clean the instrument with a soft damp cloth. Do not use solvents
or scouring agents.
• Remove the batteries you do not use the products for a long peri-
od of time.
• Keep the instrument in a dry place.
10. Waste disposal
This product has been manufactured using high-grade materials and
components which can be recycled and reused.
Never dispose of empty batteries and rechargeable bat-
teries in ordinary household waste.
As a consumer, you are required by law to take them to
your retail store or to an appropriate collection site
depending on national or local regulations in order to
protect the environment.
The symbols for the contained heavy metals are:
Cd = cadmium, Hg = mercury, Pb = lead
This product is labelled in accordance with the EU
Waste Electrical and Electronic Equipment Directive
(WEEE).
Please do not dispose of this product in ordinary house-
hold waste. As a consumer, you are required to take
end-of-life devices to a designated collection point for
the disposal of electrical and electronic equipment, in
order to ensure environmentally-compatible disposal.
7. Specifications
Temperature measuring range: -20°C to +60°C
Transmission frequency: 433 MHz
Transmission range: 30 m max
Maximum
radio-frequency power: <10 mW
Power consumption: 2x 1.5 V AA batteries (included)
Dimensions: 75 x 27 x 93 mm (L x W x H)
Weight: 87 g (instrument only)
No part of this manual may be reproduced without written consent of TFA
Dostmann. The technical data are correct at the time of going to print and may
change without prior notice.
The latest technical data and information about your product can be found by
entering your product number on our homepage.
EU declaration of conformity
Hereby, TFA Dostmann declares that the radio equipment type 30.3167 is in
compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following
internet address:
www.tfa-dostmann.de
E-Mail: info@tfa-dostmann.de
TFA Dostmann GmbH & Co.KG
Zum Ottersberg 12, D-97877 Wertheim, Germany 05/17