Cycle Guide - Kenmore 110.6813*410 Serie Manual De Uso

Damp Signal
Touch to select the Damp Signal to On or Off. When
selected, a series of beeps will sound when the load is
damp but not completely dry. This will allow you to take
clothes out of the load that do not need to dry completely.
This option is not available on Sanitize, Steam Refresh,
and the Timed cycles.
CYCLE STATUS LIGHTS
6
The indicator bar on the right side of the control will let you
know what stage of the drying cycle is in process.
Check Vent
The Check Vent indicator will light if there is a blocked
vent or low air flow.
Damp
This indicator shows that the load is partially dried
and items that you may wish to hang up or iron while
still damp may be removed.
Cool Down
The dryer has finished drying with heat, and is now
tumbling the load without heat to cool it down and
reduce wrinkling.
SENSING CYCLES –
Senses moisture in the load and shuts off when the load reaches the selected dryness level. The dry temperature
shown is the default temperature. This setting can be modified on some cycles but is not retained for future drying with this cycle. The
dryness level shown is the default dryness setting. This setting can be changed on some cycles and will be retained for future drying with
this cycle. Available options shown in bold are default settings for that cycle.
To get the most energy savings and enhanced fabric care from your dryer, use the Sensing cycles. These cycles measure the drying
air temperature and moisture levels to turn the dryer off once the load reaches the selected dryness level. For electric models, dryer
performance and results may vary with service voltage less than 240.
Items to Dry: Cycle:
Towels and Sanitize*
bedding
Jackets, Bulky/
comforters, pillows Bedding
Heavyweight items Heavy
such as towels and Duty
jeans
Corduroys, work Normal
clothes
No-iron fabrics, Casual
cottons, perm
press, linens,
synthetics
Lingerie, blouses, Delicates
washable knit
fabrics
* Extended high-heat drying cycle intended to help sanitize items such as sheets and towels. This cycle is not recommended for all
fabrics. For best results, this cycle should be run to completion to ensure sanitization and do not interrupt cycle.
If loads do not seem as dry as you would like or are drier than you would like, select More Dry or Less Dry next time you dry
†
a similar load.
6
CYCLE GUIDE – SENSING CYCLES
Dry Temp: Dry Level:
Complete
This will indicate that the selected cycle has ended and
the load may be removed from the dryer. If Wrinkle
Guard™ option has been selected, the dryer may continue
to tumble the load, even if the Complete indicator is lit.
Wrinkle Guard™
This indicator will light if the Wrinkle Guard™ option
has been selected and is running. The dryer will
periodically tumble the load for up to 150 minutes
after the cycle has ended.
Check Lint Screen
The Check Lint Screen indicator light will flash as a
reminder to clean the lint screen. It will flash until the
door is opened or a cycle is started. It will turn off
when the dryer is turned off.
START/PAUSE BUTTON
7
Touch and hold START/PAUSE button for up to 3 seconds
or until the dryer starts to begin the selected cycle; touch
again to pause a cycle.
Available
†
Options:
Wrinkle Guard™ Extended high-heat drying cycle intended
Cycle Signal to help sanitize items such as bedding and
towels. This cycle is not recommended for
all fabrics. For best results, run cycle to
completion; do not interrupt.
NOTE: Steam portion of Wrinkle Guard™
w/Steam option is disabled for this cycle.
Damp Dry Signal
Use for drying large, bulky items; do not
overfill dryer drum.
Wrinkle Guard™
Cycle Signal
Damp Dry Signal Use for drying large or heavy items.
Wrinkle Guard™
Cycle Signal
Damp Dry Signal Medium to large loads of mixed fabrics
Energy Saver and items.
Wrinkle Guard™
Cycle Signal
Damp Dry Signal For normal light- to medium-weight
Energy Saver fabrics. Drying time varies based on
Wrinkle Guard™ fabric type, load size, and dryness setting.
Cycle Signal
Damp Dry Signal For gently drying delicate items.
Energy Saver NOTE: Steam portion of Wrinkle Guard™
Wrinkle Guard™ w/Steam option is disabled for this cycle.
Cycle Signal
Cycle Details: