General Safety Rules - For All Battery Operated Tools; Work Area; Electrical Safety - Lincoln B Serie Manual Del Usario

Model 1400, 1440, 1442, 1442E, 1444, 1444E
PowerLuber Grease Gun
GENERAL SAFETY RULES - FOR
ALL BATTERY OPERATED TOOLS
WARNING! READ AND UNDERSTAND ALL
INSTRUCTIONS.
Failure to follow all instructions listed below,
may result in electric shock, fire and/or serious
personal injury.
SAVE THESE INSTRUCTIONS.

Work Area

Keep your work area clean and well lit. Clut-
tered benches and dark areas invite accidents.
Do not operate power tools in explosive atmo-
spheres, such as in the presence of
flammable liquids, gases, or dust. Power tools
create sparks which may ignite the dust or
fumes.
Keep bystanders, children, and visitors away
while operating a power tool. Distractions
can cause you to lose control.

Electrical Safety

Do not abuse the cord. Never use the cord
to carry the tool. Keep cord away from heat,
oil, sharp edges, or moving parts. Replace
damaged cords immediately. Damaged cords
may create a fire. Applies only to tools with a
separable battery pack.
A battery operated tool with integral batteries or
a separate battery pack must be
recharged only with the specified charger for
the battery. A charger that may be suitable for
one type of battery may create a risk of fire
when used with another battery.
Use battery operated tool only with specifically
designated battery pack. Use of any other bat-
teries may create a risk of fire.
Personal Safety
Stay alert, watch what you are doing, and use
common sense when operating a power
tool. Do not use tool while tired or under the
influence of drugs, alcohol, or medication. A
moment of inattention while operating power
tools may result in serious personal injury.
Dress properly. Do not wear loose clothing or
jewelry. Contain long hair. Keep your
hair, clothing, and gloves away from moving
parts. Loose clothes, jewelry, or long hair can
be caught in moving parts.
Avoid accidental starting. Be sure switch is in
the locked or off position before inserting
battery pack. Carrying tools with your finger on
the switch or inserting the battery pack into a
tool with the switch on invites accidents.
Remove adjusting keys or wrenches before
turning the tool on. A wrench or a key that is left
attached to a rotating part of the tool may result
in personal injury.
Page Number - 2
Do not overreach. Keep proper footing and bal-
ance at all times. Proper footing and
balance enable better control of the tool in
unexpected situations.
Use safety equipment. Always wear eye protec-
tion. Dust mask, non-skid safety shoes,
hard hat, or hearing protection must be used
for appropriate conditions.
Tool Use and Care
Use clamps or other practical way to secure
and support the workpiece to a stable
platform. Holding the work by hand or against
your body is unstable and may lead to loss of
control.
Do not force tool. Use the correct tool for your
application. The correct tool will do the job bet-
ter and safer at the rate for which it is designed.
Do not use tool if switch does not turn it on or
off. A tool that cannot be controlled with the
switch is dangerous and must be repaired.
Disconnect battery pack from tool or place
the switch in the locked or off position before
making any adjustments, changing accesso-
ries, or storing the tool. Such preventive safety
measures reduce the risk of starting the tool
accidentally.
Store idle tools out of reach of children and
other untrained persons. Tools are
dangerous in the hands of untrained users.
When battery pack is not in use, keep it away
from other metal objects like: paper clips,
coins, keys, nails, screws, or other small metal
objects that can make a connection from
one terminal to another. Shorting the battery
terminals together may cause sparks, burns,
or a fire.
Maintain tools with care. Keep cutting tools
sharp and clean. Properly maintained tools
with sharp cutting edge are less likely to bind
and are easier to control.
Check for misalignment or binding of moving
parts, breakage of parts, and any other
condition that may affect the tool's operation. If
damaged, have the tool serviced before using.
Many accidents are caused by poorly main-
tained tools.
Use only accessories that are recommended
by the manufacturer for your model.
Accessories that may be suitable for one
tool may create a risk of injury when used on
another tool.
Service
Tool service must be performed only by quali-
fied repair personnel. Service or
maintenance performed by unqualified person-
nel may result in a risk of injury.
Form 402103