Memory Deletion - Stobag MOVENO DSRCE-V Instrucciones Y Advertencias Para La Instalación Y El Uso

4.3.1) Memorisation of the intermediate position "I"
If an intermediate positions "I" has been memorised, the awning can be manoeuvred into the programmed position by pushing the ▼ and ▲
buttons of the transmitter together. Proceed as follows to memorise the intermediate positions:
Table "A4" Programming of the intermediate position "I"
Move the shutter into the desired intermediate position "I" by means of the ▲ ■ ▼
1.
buttons of a remote control.
Keep the ■ button pushed until a beep is heard (after about 5 seconds).
2.
Release the ■ button and push it again for another 5 seconds until 4 rapid beeps are heard.
3.
Push the ▼ ▲ buttons together until 3 beeps signal that the position has been memorised.
4.
4.3.2) Cancellation of the memorised position
In order to modify the memorised positions, they must firstly be cancelled and then the new positions programmed again.
Table "A5" Cancellation of the intermediate position "I"
Push and hold the ■ button of an already memorised transmitter until a beep is heard
1.
(after about 5 seconds).
Release the ■ button and push it again for another 5 seconds until 4 rapid beeps are heard.
2.
Push the ▲ ▼ buttons together until 5 beeps signal that the intermediate position has
3.
been cancelled.
Now the new intermediate position can be programmed (Table "A4").
Table "A6" Cancellation of the "0" and "1" positions
Push and hold the ■ button of an already memorised transmitter until a beep is heard
1.
(after about 5 seconds).
Release the ■ button and push it again for another 5 seconds until 4 rapid beeps are heard.
2.
Push the ▲ button (if the automatic or manual programming has been performed) or the ▼
3.
button (if the semi-automatic programming has been performed), until 5 beeps signal that
the "0" and "1" positions have been cancelled.
WARNING: After having cancelled the "0" and "1" positions the shutter will move in the hold-to-run mode and the new positions need to be
memorised (Table "A3").

4.4) Memory deletion

If you need to delete all the transmitter and the programmed operations, carry out the procedure shown in table A7.
The memory can be deleted:
• with a non-memorized transmitter starting from point A.
• with a previously memorized transmitter starting from point No. 1.
The following can be deleted:
• only the memorized transmitters, finishing at point No. 4
• all data (transmitters, sensor level, TTBUS address, etc.), completing the procedure until point 6.
Table "A7" Memory deletion
➡
A. Switch the motor off, activate the Step-by-Step input (by connecting the White cable
with the White/Black one) and keep it active until the end of the procedure.
B. Power the motor and wait for the initial beeps.
➡ Press and hold down button ■ on a transmitter (about 5 seconds) until you hear
1.
a beep; then release it.
Hold down the ▲ button on the transmitter until you hear 3 beeps;
2.
release the ▲ button exactly during the third beep.
Hold down button ■ on the transmitter until you hear 3 beeps;
3.
release button ■ exactly during the third beep.
➡
Hold down the ▼ button on the transmitter until you hear 3 beeps;
4.
release the ▼ button exactly during the third beep.
5. To cancel everything:
Press both ▲ and ▼ within 2 seconds
Cancellation is confirmed by releasing buttons ▲ and ▼ on the first of the 5 beeps.
6.
30
Example
5s
5s
Example
5s
5s
Example
5s
5s
Example
PP
5s
www.stobag.com