Fellowes POWERSHRED 99Ms Guia De Inicio Rapido página 3

Ocultar thumbs Ver también para POWERSHRED 99Ms:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

BASIC SHREDDING OPERATION
PAPER OR CARD
1
Continuous operation:
Up to 15-minutes maximum
NOTE: Shredder runs briefly
after each pass to clear entry.
Plug in and put
Continuous operation beyond
disconnect power
15-minutes will trigger
switch in ON (I) position
25-minute cool down period.
ADVANCED PRODUCT FEATURES
Patented SafeSense
®
Stops shredding immediately when
hands touch the paper opening.
SAFESENSE
®
TECHNOLOGY OPERATION
Stops shredding immediately when hands touch the paper opening.
SET-UP AND TESTING
1
2
Turn the shredder ON
Touch test area and
( ) to activate SafeSense
look for the SafeSense
®
indicator to illuminate
For more information about all of Fellowes Advanced Product Features go to www.fellowes.com
PRODUCT MAINTENANCE
OILING SHREDDER
All micro-cut shredders require oil for peak performance. If not oiled, a
machine may experience diminished sheet capacity, intrusive noise when
shredding and could ultimately stop running. To avoid these problems, we
recommend you oil your shredder each time you empty your waste bin.
FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE
1
2
*Apply oil across entry
Press and hold forward ( )
2-3 seconds
*Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250
TROUBLESHOOTING
Overheat Indicator: When the Overheat Indicator is illuminated, the shredder has exceeded its maximum operating temperature and needs to cool down. This indicator will remain
illuminated and the shredder will not operate for the duration of the recovery time. See Basic Shredding Operation for more information about the continuous operation and
recovery time for this shredder.
Bin Open: The shredder will not run if the bin is open. When illuminated, close the bin to resume shredding.
Bin Full: When illuminated, the shredder waste bin is full and needs to be emptied. Use Fellowes waste bag 36053.
Remove Paper: When illuminated, press reverse (
SafeSense
®
Indicator: If hands are too close to the paper entry, the SafeSense
is active for 3 seconds, the shredder will automatically turn off and the user must press the power button on the control panel to resume shredding.
2 2
Press ON (I) to
activate (blue)
Technology
SilentShred™ Technology
SilentShred™ noise quality
shreds without noisy disruptions.
3
4
SafeSense
is active and
If hand is held on SafeSense
®
working properly
area more than 3 seconds,
®
shredder will shut off
) and remove paper. Reduce paper quantity to an acceptable amount and refeed into paper entry.
3
4
Feed paper/card
When finished
shredding set
straight into paper
entry and release
to OFF ( )
WHEN IN SLEEP MODE
1
In sleep mode
®
CLEANING AUTO-START INFRARED SENSORS
Paper detection sensors are designed for maintenance free operation. However, on rare occasions the sensors
may become blocked by paper dust causing the motor to run even if there is no paper present.
(Note: two paper detection sensors are located in the center of the paper entry)
TO CLEAN THE SENSORS
2
1
Turn off and unplug
Locate Auto-start
shredder
infared sensor
®
indicator will illuminate and the shredder will stop shredding. If SafeSense
Sleep Mode
Energy saving feature shuts down automatically
after 2 minutes of no shredding activity
SLEEP MODE OPERATION
Energy saving feature shuts down the shredder after
2 minutes of inactivity
3
2 2
or
To get out of sleep mode
insert paper
touch control panel
.
3
4
Dip cotton swab in
Using cotton swab, wipe
rubbing alcohol
away any contamination
from the paper sensors
®
3

Publicidad

Tabla de contenido
loading

Tabla de contenido