Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame rail
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75547F
Wrenches: 17mm, 11/16
Drill Bits: None
Note:
Fasteners typical both sides
j
Qty. (4)
Hex Bolt M10X1.25X30 CL8.8
k
Qty. (4)
Conical Washers
l
Qty. (1)
3/8-16 U-Bolt
1.
Lower exhaust by removing rubber isolators from muffler hangers. Remove the outside isolator first then the inside isolator.
Spraying a lubricant or soapy water on the metal hanger rod and the rubber isolator helps removal.
2.
Raise hitch into position.
3.
Install M10 fasteners as shown.
4.
Install the 3/8 U-Bolt through the vehicle tie down hook and through the tie down hook attachment of the receiver. Install flat
washer, lock washers and 3/8 hex nuts as shown above.
5.
Tighten all fasteners to the required torque specification.
6.
Raise exhaust back into position and re-install rubber isolators.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
2007, 2011 Cequent Performance Products
z
Installation Instructions
Honda CR-V
Fascia
Exhaust shown lower
Tighten all 3/8-16 GR5 fasteners with torque wrench to 30 Lb.-Ft. (41 N*M)
Tighten all M10 CL8.8 fasteners with torque wrench to 38 Lb.-Ft. (52 N*M)
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location:
Inside isolator
Tie
down
hook
l
m
n
o
m
Qty. (2)
Flat Washer
n
Qty. (2)
Lock Washer
o
Qty. (2)
3/8 Hex Nut
75547N
Part Numbers:
75547
87440
44575
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
Not For Use With Spring Bars
3500 (1589 Kg)
525 (238 Kg)
Existing
weldnuts
typical
k
j
6-21-11
Rev. B
Publicidad
Manuales relacionados para Cequent Performance Products 75547
Resumen de contenidos para Cequent Performance Products 75547
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2007, 2011 Cequent Performance Products Sheet 1 of 3 75547N 6-21-11 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2007, 2011 Cequent Performance Products Feuille 2 de 3 75547N 6-21-11 Rev.
- Página 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. 2007, 2011 Cequent Performance Products Hoja 3 de 3 75547N 6-21-11 Rev.