GreenWorks 2000507 Manual De Utilización página 23

EN
FR DE ES IT PT
SHARPENING THE SAW CHAIN
See figure 16 - 21
When the chain penetrates into wood with difficulty, it
needs sharpening as follows:
Put the chain under tension.
Fasten the bar in a vice so that the chain can slide.
Fasten the file to the file holder and place it on cutter
at 35° angle.
File with forward strokes only until all the worn out
parts of the cutting edge are taken away.
Count the number of strokes given to the cutter as
a reference and file away with the same number of
strokes on all other cutters.
If the depth gauge protrudes from the template after
sharpening a few times, reset its level. Use a flat file.
Finally, round off the depth gauge.
NOTE: It is recommended to have the deep or important
sharpening carried out by a service agent who is equipped
with electric sharpener.
GUIDE BAR MAINTENANCE
When you have finished working, clean out the groove
and the oil passages with a scraping hook.
Periodically trim the sides of rails using a flat file. If not
done in the long run, the feather edges might break
away and damage the bar.
If one rail is higher than the other one, it is necessary
to make it even with a flat file then smooth it with a file
or fine grain abrasive paper.
WARNING
When servicing, use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
WARNING
To avoid serious personal injury, always remove the
battery pack from the tool when cleaning or performing
any maintenance.
GENERAL MAINTENANCE
Before each use, inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps,
etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts
are replaced. Please call Greenworkstools Customer
Service for assistance.
NL SV DA NO FI HU CS RU
English
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
Do not at any time let brake liquids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
Only the parts shown on the parts list are intended to
be repaired or replaced by the customer. All other parts
should be replaced at an authorised service centre.
STORAGE
STORING THE PRODUCT
DISPOSAL
Power tools and accessories contain
large amount of valuable resources
and plastics that can be recycled.
Waste electrical products should not be
disposed of together with household
waste. Please recycle where facilities
exist. Check with your local authority or
retailer for recycling advice.
The
and the environment. It must be removed and disposed
of separately at a facility that accepts lithium-ion batteries.
Li-ion battery. This product has been marked with a symbol
relating to separate collection for all battery packs and battery
pack. It will then be recycled or dismantled in order to reduce
the impact on the environmrnt. Battery packs can be hazardous
for the enviroment and for human health.
20
RO PL SL HR ET
WARNING
Remove the battery pack from the unit before storing.
Clean all foreign material from the unit.
Store it in a place that is inaccessible to children.
Keep away from corrosive agents such as garden
chemicals and de-icing salts.
Store and charge your batteries in a cool area.
Temperatures above or below
temperature will shorten battery pack life.
Never store batteries in a discharged condition. Store
battery packs in a 30%-50% charged condition.
Store the battery pack where the temperature is below
27 FIC and away from moisture.
All batteries gradually lose their charge. The higher
the temperature, the quicker they lose their charge.
If you store your unit for long periods of time without
using it, charge the pack as normal every six months
of storage. This practice will prolong battery pack life.
battery contains material which is hazardous to you
LT LV SK BG
normal room