FARFISA INTERCOMS KM8262W Manual Del Usuario página 5

Using the push-button keyboard for
programming
Press button " " and " " to enter addresses
or codes.
:Press this button to access the
programming mode (when pressed for 4
seconds with off-hook handset), confirm
address or code programming or go to
the next programming step.
: Press this button to increase the value
you want to enter. Press the button for a
number of times equal to the digit you want
to enter (digit 1 = 1 time; digit 9 = 9 times;
digit 0 = 10 times button " ").
Pressure of button " " is confirmed by an acoustic
tone.
Entering the programming mode
To enter the programming mode you must:
pick up the handset and leave it off-hook
during the entire programming step;
press button " " for at least 4 seconds until
you receive the confirmation tone.
Entering codes or addresses
- Codes and/or addresses must have three
digits (hundreds, tens, units); codes and/or
addresses with tens and units or units only
must be completed by adding zeros. For
example, address 96 will become 096 and
address 5 will become 005.
- Digits must be entered individually, by
pressing the button " " for a number of times
"n", where "n" is the value of the digit you want
to enter, followed by a pause of about 2 seconds
before you go to the next digit (a tone in the
handset will tell you when to go to the next
digit).
For example, to enter code 096 you must:
- press button " " 10 times to enter digit 0, wait
for 2 seconds until you hear a sound in the
handset.
- press button " " 9 times to enter digit 9, wait
for 2 seconds until you hear a sound in the
handset.
- press button " " 6 times to enter digit 6, wait
for 2 seconds until you hear a sound in the
handset.
- press button " " to confirm entering and go
to the next programming step. An acoustic
tone in the handset will confirm that the code
has been stored and you can go to the next
step.
Exiting the programming mode
You will automatically exit the programming
mode after pressing button "
7th programming, i.e. "code to assign to button
" ". You can also exit the programming mode at
any time by hanging up the handset. Settings
will not be saved if you exit the programming
mode without confirming with button "
You will also exit the programming mode
automatically if you make a mistake or an
operation that is not permitted when entering a
code. In this case, you must access the
programming mode again to continue.
Automatic programming
You can use the automatic programming mode
to save the intercom address from the external
station.
Automatic programming procedure
To enter the automatic programming mode you
must:
a) enter the programming mode following the
instructions described in " Entering the
programming mode ";
b) make a call from an external station within
2 minutes. In case of installations with digital
push-button keyboard TD2100MA, key in
the number you want to assign to the intercom
and press "
digital encoder CD2132MA or CD2134MA
press the button you want to assign to the
user on the push-button keyboard. When the
call is received, the videointercom is
programmed automatically, you hear the call
tone in the handset and the videointercom is
turned on, showing the calling external station.
Close and pick up the handset to start a
conversation with the external station and
check the correct operation of the system;
c) at the end of the conversation hang up the
handset to exit the automatic programming
mode.
Simplified programming
The simplified programming mode allows for
quick saving of the videointercom address.
Simplified programming procedure
To enter the simplified programming mode you
must:
a) enter the programming mode following the
instructions described in " Entering the
programming mode ";
b) enter the three digits of the user address.
Digits must be entered individually, by
pressing the button " " for a number of times
"n", where "n" is the value of the digit you want
to enter, followed by a pause of about 2
seconds before you go to the next digit (a
sound in the handset will tell you when to go
to the next digit).
For example, to enter code 096 you need to:
- press button " " 10 times to enter digit 0, wait
for 2 seconds until you hear a sound in the
handset.
- press button " " 9 times to enter digit 9, wait
for 2 seconds until you hear a sound in the
handset.
- press button " " 6 times to enter digit 6, wait
for 2 seconds until you hear a sound in the
handset.
c) hang up the handset as soon as you hear
the confirmation tone in the handset to exit
the simplified programming mode.
" to confirm the Manual programming
The manual programming mode allows you to
enter the user address, assign the internal
address and codes to buttons " " and " ".
Manual programming procedure
".
To enter the manual programming mode you
must:
a) enter the programming mode following the
instructions described in " Entering the
programming mode ";
b) programme the following functions in
sequence:
1) User address – this code allows you to
receive an external call, turn on the
videointercom, have a conversation and
open the door at the calling external station.
For information on address entering see
" Entering codes or addresses ".
". In case of installations with
2) Internal address – these codes are used
to identify the videointercoms installed in
the apartment (max. 3). In case of one
videointercom only, the internal code must
be 000 (default value); if other video-
intercoms are present (max. other 2) you
must assign codes 001 and 002 to them.
By entering these codes, all videointercoms
will ring when an intercom call is made; if
you prefer not to activate the intercom ring
in the third videointercom, you must assign
code 003 instead of 002.
For information on code entering see
" Entering codes or addresses ".
3) Address of external station 1 associated
with button " " – address of external
station 1 you want to connect with when
button " " is pressed. If the installation
only includes one external station, the
address does not need to be stored, since
it will be automatically acquired upon the
first call.
4) Address of external station 2 associated
with button " " – address of external
station 2 you want to connect with when
button " " is pressed. This code does not
need to be saved if the installation does not
include two external stations.
For information on code entering see
" Entering codes or addresses ".
5) Address of external station 3 associated
with button " " – address of external
station 3 you want to connect with when
button " " is pressed. This code does not
need to be saved if the installation does not
include three external stations.
For information on code entering see
" Entering codes or addresses ".
6) Address of external station 4 associated
with button " " – address of external
station 4 you want to connect with when
button " " is pressed. This code does not
need to be saved if the installation does not
include four external stations.
For information on code entering see
" Entering codes or addresses ".
7) Address associated with button " " – to
call users from other apartments you must
enter their user address (001 to 200). Enter
code 000 if you want to use this button to
make intercom calls between intercoms in
the same apartment.
For information on code entering see
"Entering codes or addresses".
In "Manual programming" mode the 7 steps
above must be performed in sequence from
step 1 to step 7. Each step must be confirmed
by pressing button " ". Press button "
again if you want to skip a programming
operation and go to the next one. For example,
after you have programmed the "user
address (step 1)" and confirmed it by pressing
button " ", you will automatically go to the
"internal address (step 2)". If this setting is
not necessary, press button "
and go to "address of external station 1 to
be assigned to button (step 3)". Now you
can enter the code. Otherwise you can press
button " " 4 times to skip steps 3, 4, 5 and
6 and go to "address associated with button
" (step 7)". Again, you can enter the code or
press button " " to skip this programming.
Mi 2334/1
"
" to skip it
- 5 -