Beko HNS 61210 X Manual Del Usario página 12

Mounting
The cooker hood may be installed on the wall or on the base
of a cabinet; if supplied, use the hole gauge H to drill the cor-
rect distance, otherwise lean the cooker hood on the wall or
on the base of the cabinet and mark the holes with a pencil.
Wall mounting - Insert the wall screw anchors J in the drilled
holes and the two K screws in the upper drill holes, remove
the grill and hook the cooker hood to the 2 screws, finally from
the inside, insert the third screw L and lock them all in.
Cabinet fixing - Affix the cooker hood with the 4 M screws
from inside the cabinet.
Operation
The hood is fitted with a control panel with aspiration speed
selection control and a light switch to control cooking area
lights.
Always open the vapour catcher N*.
If your product is provided with an electrically or mechanically
activated valve, the keys and/or the buttons and/or the han-
dles available are for controlling the lights and for opening and
closing the valve.
Maintenance
Cleaning
Clean using ONLY the cloth dampened with neutral liquid
detergent. DO NOT CLEAN WITH TOOLS OR INSTRU-
MENTS. Do not use abrasive products. DO NOT USE AL-
COHOL!
Grease filter
Traps cooking grease particles.
If situated inside the support grill, it may be one of the follo-
wing types:
Paper filter must be replaced once a month or if colouring
appears on upper side, in such cases the colouring is evident
through the grill openings.
Metallic filter must be cleaned once a month, with non abra-
sive detergents, by hand or in dishwasher on low temperature
and short cycle.
When washed in a dishwasher, the grease filter may discolour
slightly, but this does not affect its filtering capacity.
In order to remove the grease filter open the grill via the P
hooks and free the R1 or R2 stoppers.
The self-supporting metal filter does not include a support
grill, in order to remove the filter – pull the release springs P4
backwards and slide the filter downwards.
Charcoal filter (filter version only)
It absorbs unpleasant odors caused by cooking.
The saturation of the charcoal filter occurs after more or less
prolonged use, depending on the type of cooking and the
regularity of cleaning of the grease filter.
In any case it is necessary to replace the cartridge at least
every four months.
The charcoal filter may NOT be washed or regenerated.
It may be one of the following types:
Rectangular S1 or S2 or S3:
Mounting (S1 or S2) : insert the rear side T and hook further
to the front (U).
Mounting (S3): Remove the cover W by rotating the O knobs
to 90° ,fit the filter inside and lock in place with the central
knob O, then close the cover.
Proceed in the inverse for dismounting.
Circular (V1-V2-V3-various models):
Bayonet mount position the filter in the middle of the motor
protection grill covering ensuring that the reference to X1 or
X2 or X3 on the carbon filter match the Y1 or Y2 references
on the conveyor, then turn clockwise; in case of dismounting
turn anticlockwise, if provided with a Z tape remember to
gently lift first.
Replacing lamps
Disconnect the appliance from the electricity.
Warning! Prior to touching the light bulbs ensure they are
cooled down.
Replace the old light bulb with the one of the same type as
specified in the feature label or near the light lamp on the ho-
od.
Remove the grill.
Remove the damaged light and replace it with a new one (see
the table below):
Lamp
Voltage (V)
230
ILCOS D Code
(according IEC 61231)
HSGSB/C/UB-28-230-E14-67
Put the grill back.
If the lights do not work, make sure that the lamps are fitted
properly into their housings before you call for technical assi-
stance.
11
Power (W) Socket
28
Dimension (mm)
67 (Light Center
Length)
E14