Installation Instructions; Emergency Procedures; Maintenance Instructions - BriskHeat HotBelt HB1001 Manual De Instrucciones

INSTALLATION INSTRUCTIONS

Failure to follow these instructions could result in
property damage, personal injury, or death.
Surface Preparation:
Always install your heater on a clean even surface for optimum performance and longevity. Debris and
residue on the surface can not only damage your heater but may also reduce the effectiveness of the
heater by reducing the heat transfer between the surface and the heater.
•
Remove or avoid contact with sharp edges including rough corners, weld spatter, exposed bolts,
etc.
•
Remove or avoid contact with rust, stickers, or other coverings.
•
Remove oil, moisture, gel and other liquids.
Instructions:
Wrap the heater around the cylinder and secure the heater using the extra-long strap. It is important that
the heater fits tightly. Check to make sure that the area behind the thermostat which is near the edge of
the heater is making good contact with the surface of the cylinder.
After positioning the heater on the cylinder, insert the plug into a polarized outlet (appropriately rated for
your heater's voltage). When plugged in, the heater will automatically begin to heat. When the surface
temperature of the cylinder reaches approximately 158°F (70°C) at the built-in sensor, the heater will
automatically shut-off. The heater will automatically begin to heat again when the surface temperature of
the cylinder drops to approximately 147°F (64°C) at the built-in sensor. The heater will begin to cycle on/
off under normal thermostatic control to maintain the cylinder surface temperature at 147°F (64°C) to
158°F (70°C) at the built-in sensor.
The built-in thermostat is designed to maintain approximately 120°F (49°C) actual surface temperature of
the cylinder in 32°F (0°C) ambient conditions. Variations in ambient temperature and material contents
within the cylinder may affect the surface temperature of the cylinder.
DO NOT leave the heater unattended.
NOT suitable for use in wet conditions.
DO NOT attempt to disassemble the heater or make any modifications to the heater. The heater is
engineered for maximum performance and reliability.
ALWAYS inspect the heater and cordset before each use to ensure it is free of damage and loose or
frayed wires.
DO NOT Attempt to use the heater if the heater or cordset is damaged or has loose or frayed wires.
Contact BriskHeat if repair is necessary.
®
© BriskHeat Corporation. All rights reserved.
HotBelt™
Wrap Around Refrigerant Jug Warmer
5

EMERGENCY PROCEDURES

Read and understand these procedures prior to using this heater.
Disconnect power to the heater in the event of an emergency.
Electric Shock:
•
Do not touch the injured person while they are still in contact with the electrical current.
•
Call your local emergency service if the injured person experiences: severe burns, confusion,
difficulty breathing, heart rhythm problems, cardiac arrest, muscle pain and contractions, seizures
or a loss of consciousness.
Minor Burns:
•
Hold the burned area under cool running water for 10-15 minutes.
•
Remove rings or other tight items from burned area.
Major Burns:
•
Call your local emergency service.
•
Protect the person from further harm.
•
Remove rings or other tight items from burned area.
•
Monitor breathing and perform CPR if necessary.
Fire:
•
Call your local emergency service.
•
If it is safe to do so, use a fire extinguisher to fight the fire, otherwise evacuate to a safe distance
and wait for help to arrive.
•
This heater is built from material that will not support a flame but could ignite nearby combustible
material.

MAINTENANCE INSTRUCTIONS

Anyone who reads and understands these instructions is
qualified to maintain this heater.
Maintenance:
•
All maintenance should be performed after heater has cooled to room temperature and with the
electricity disconnected.
•
This product should be inspected prior to being installed and at least every 3 months during use.
•
Dirt, oil, grease or other foreign matter can be removed with a damp rag and mild household
cleaners.
•
Do not attempt to repair a damaged heater.
®
© BriskHeat Corporation. All rights reserved.
HotBelt™
Wrap Around Refrigerant Jug Warmer
6