Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Jaws for PureFlow
RIDGID
®
Jaws for PureFlow
PureFlow
®
Fittings onto
3
/
",
8
and FostaPEX™ tubing. An individual jaw is required for each size
tubing.
Read these instructions, the Press Tool operator's manual, the
fitting manufacturer's installation in struc tions and any other
applicable information be fore using these jaws. Fail ure to un -
der stand and follow all instructions may result in extensive
property damage, serious personal injury or death.
Contact the Ridge Tool Company Technical Services De part ment at
(800) 519-3456 or TechServices@ridgid.com if you have any questions.
Pressing Tool Safety
• Always wear eye protection. Protect your eyes from dirt and other
foreign objects.
• Only use a RIDGID Press Tool with RIDGID jaws for PureFlow
Use of other tools may damage the jaws or make improper connec-
tions.
• Only use RIDGID jaws for PureFlow
tings. Other uses or modifying the jaws for other applications may
damage the press tool, the jaws, make improper connections or
cause injury.
• Keep your fingers and hands away from the jaws during the
press cycle. Your fingers or hands can be crushed, fractured or
amputated if they become caught between the jaws, or between the
jaws and any other object.
• Never attempt to repair a damaged jaw. A jaw that has been weld-
ed, ground, drilled or modified in any manner can shatter during
pressing resulting in serious injury. Discard the entire damaged jaw.
Replace with a new jaw. Never replace individual components
except for springs and retaining rings. Failure to replace the entire
jaw may result in component failure and serious injury.
SAVE THESE INSTRUCTIONS!
Selection of appropriate materials and joining methods is the
NOTICE
responsibility of the system designer and/or installer. Before any installa-
tion is attempted, careful evaluation of the specific service environment,
including chemical environment and service temperature, should be
completed. Consult fitting system manufacturer for selection information.
Compact Jaws For PureFlow
RIDGID Compact Series jaws only function with RIDGID Compact Ser -
ies Pressing Tools.
Catalog No.
Size
17003
17008
19813
17013
17018
22683
1
22688
1
Standard Jaws For PureFlow
RIDGID Standard Series jaws only function with RIDGID Standard Ser -
ies Pressing Tools.
Catalog No.
Size
22653
22658
22663
22668
22673
22678
Printed in U.S.A.
®
Instruction Sheet
®
are de signed to mechanically press
1
/
",
5
/
",
3
/
", 1", 1
1
/
" and 1
1
/
" ViegaPEX™
2
8
4
4
2
WARNING
to press PureFlow
®
®
:
Weight
"
3
/
2.5 lbs. (1.1 kg)
8
"
1
/
2.5 lbs. (1.1 kg)
2
"
5
/
2.5 lbs. (1.1 kg)
8
"
3
/
2.5 lbs. (1.1 kg)
4
"
1
2.5 lbs (1.1 kg)
"
1
/
2.5 lbs (1.1 kg)
4
"
1
/
2.5 lbs (1.1 kg)
2
®
:
Weight
"
1
/
4 lbs. (1.8 kg)
2
"
5
/
4.25 lbs. (1.9 kg)
8
"
3
/
4.5 lbs. (2.0 kg)
4
"
1
4.5 lbs (2.0 kg)
"
1
1
/
4.75 lbs (2.2 kg)
4
"
1
1
/
6.5 lbs (2.9 kg)
2
Ridge Tool Company/Elyria, Ohio, U.S.A.
Inspection/Maintenance
1. To aid inspection and prevent tool slippage, remove oil, grease and
dirt from tool and jaw handles.
2. Inspect the jaw daily for obvious cracks, binding, breakage, miss ing
parts, excessive wear or other signs of damage. If any of these con-
ditions are found, the jaw should be discarded and replaced.
A jaw component that has been welded, ground, drilled,
WARNING
or modified in any manner can fail during use, resulting in severe injury.
Discard and replace damaged jaws.
3. Clean and lubricate the moving parts of the jaw on a regular basis
to prevent wear and maximize tool life. Make sure the jaw arms
move freely and the return spring closes the jaw. Do not use ag -
gressive, abrasive cleaning methods that could alter critical jaw
dimensions and result in improper crimps and other problems.
Operating Instructions
Pressing The Fitting
1. Insert jaw into press tool per the instructions in press tool opera-
tor's manual.
2. Prepare tubing, fitting and sleeve as directed in the fitting manufac-
turer's installation instructions.
3. Make sure the tubing is inserted to the proper depth in fitting.
®
.
4. Squeeze jaw arms to open the jaw (Figure 1).
Fit -
®
Figure 1 – Opening The Jaw
5. Place open jaw around the fitting. Make sure the raised lip of the
stainless steel sleeve is properly aligned with the jaw (Figure 2) .
Figure 2 – Placing Jaw Squarely Onto PureFlow
6. Make sure the jaw is square to the tubing (Figure 2) and de press
tool trigger. The press cycle takes about six (6) seconds. Once a
press cycle be gins and the rollers contact the jaw arms, the tool will
lock-on and automatically complete the press cycle. Releasing the
trigger will not stop the tool once the pressing process has begun.
This assures consistent, repeatable pressed connection integrity.
12/08
®
Fitting
085-210-011.10

Publicidad

loading

Resumen de contenidos para RIDGID 17003

  • Página 1 3. Make sure the tubing is inserted to the proper depth in fitting. • Only use a RIDGID Press Tool with RIDGID jaws for PureFlow ® Use of other tools may damage the jaws or make improper connec- 4.
  • Página 2 FRANÇAIS Systèmes PureFlow ® pour mâchoires « Standard » Mâchoires pour colliers PureFlow ® – Les mâchoires standard de RIDGID ne peuvent fonctionner que sur les sertisseuses RIDGID du type Standard. Fiche d’instructions Ø Réf. Catalogue Poids Les mâchoires RIDGID ®...
  • Página 3 Seguridad de la Selladora • Use siempre protección para los ojos. Protéjalos para que no les entren mugre u objetos foráneos. • Sólo emplee una Selladora RIDGID con mordazas para Figure 2 – Positionnement des mâchoires à ciseaux sur le raccord PureFlow ®...
  • Página 4 Mordazas para PureFlow ® – Hoja de instrucciones Mordazas Compact para PureFlow ® Las Mordazas serie Compact de RIDGID sólo funcionan con Selladoras serie Compact de RIDGID. No. en el Catálogo Tamaño Peso 17003 pulg. 1,1 kg (2,5 lbs.) 17008 pulg.

Este manual también es adecuado para:

170081981317013170182268322688 ... Mostrar todo